AUTOCALCS MODEL SCRIPT GUIDE A model script is plain text that describes a structure, one item per line: the points (nodes), the beams and columns between them (members), supports, loads and load combinations. Paste it into File Manager > Import > Model script and press Create model for a new project, or use Model Script in the ribbon to replace the model in the open file. Both need you to be signed in. If the script has problems, nothing is created and each problem is listed with its line number. Plates (slabs and walls) are meshed and openings cut exactly as when they are drawn in the app. Sections and materials come from the AutoCalcs library. A script either names the library item (lib="...", see section 3 and the list in section 5) or gives just a name such as "Columns" as a placeholder and leaves the pick for later: after the model is created, pick a library item or one of your own custom sections or materials for it in the Sections and Materials dialogs, and every member using that name updates at once. When the model is created, the message that confirms it lists the library items the script picked. The model can't be analysed until every section and material has been picked. ============================================================================ 1. USING AN AI ASSISTANT (ChatGPT, Claude, Gemini, ...) ============================================================================ 1. Copy this whole guide (the "Copy guide for AI" button does this). 2. Paste it into the assistant, then describe your structure underneath: spans, heights, supports, the sections and material you want (or the country whose sections to use), loads and the combinations you need. Say metric or imperial. 3. Paste the script it returns into the box and press Create model. If problems are listed, paste them back to the assistant and ask it to fix the script. ============================================================================ 2. INSTRUCTIONS FOR THE AI ASSISTANT ============================================================================ You are writing an AutoCalcs model script for a structural engineer. Follow these rules exactly. The format is checked strictly; anything not described in section 3 is rejected. Output - Reply with the complete script in a single code block, nothing else in the block. Notes go on their own lines starting with #. - If units, the main dimensions, supports or loads are missing from the request, ask before writing. Write any assumption you make as a # comment at the top of the script. Format - The first line is "units metric" or "units imperial". - One item per line. Ids (names like N1, C1, G) start with a letter or digit, use letters, digits and . _ : - only (no spaces, at most 96 characters, at most 15 if all digits) and are case-sensitive. Each kind has its own ids: nodes; members and plates; load cases and combinations; sections; materials; openings; diaphragms; links. Text with spaces goes in "double quotes". - Don't name a section hinged or pinned (those are member words). - Define everything before it is used. The usual order is: units, library, sections and materials, nodes, members, plates and openings, diaphragms, links, load cases, loads, and combinations last. - Numbers only: no arithmetic (write 7, not 3.5*2), no units after coordinates or loads, no thousands separators. Decimals and scientific notation are fine (0.25, 1.2e-5). Only at=, from= and to= accept a unit (2m / 6ft) or a percentage (50%). Sections and materials - Never write section or material properties (no E=, A=, Ix=, fy=). - Name library items with lib= using only names that follow the patterns in section 5. Library names are file names such as UB_310x40_G300 (Australian 310UB40.4, grade 300) or W_12x26; write them that way, not as 310UB40.4. - Sections: write "library " after units. Countries: Australia, Brazil, Canada, China, Europe, India, Japan, New_Zealand, United_Kingdom, United_States. A section from another country takes country= on its line. - If a name exists in more than one folder of that country (for example RHS grade 350 and 450 folders, or every European section in two grade folders), add the folder: lib="RHS_Rectangular_350/RHS_100x50x3". - Materials: write the end of the folder path, enough to pick one item, e.g. lib="Australia/Steel/STEEL" (the item listed under Metric/Australia/Steel), lib="Metric/Steel/STEEL" or lib="Imperial/Steel/STEEL". "STEEL" alone matches several materials and is rejected. Use only grades the list in section 5 shows. - Timber: the section gives the size, the material gives the grade and strength (e.g. a Seasoned_Timber size with an MGP_10 material). - Use a placeholder (no lib=) when you are not sure a size exists, when the engineer wants their own custom section or material, or when the size is not decided: put the intent in its name (section COL "310UC97", section BM "Custom plate girder") and say so in a # comment. The engineer picks it after import. Geometry - Global axes (right-handed): X and Z are horizontal, Y is vertical, pointing up. Node coordinates are x y z in that order, so a 4 m column is node A 0 0 0 / node B 0 4 0. Floor plans are in X-Z; heights are Y. Seen from above with +X to the right, +Z points down the page. Unless the engineer says otherwise, put the main plan length along X and the depth along Z, with the origin at a corner and all coordinates zero or positive. - Members only connect where they share a node. Where a beam meets a column or another beam part-way along, put a node there and split the member. Never let members overlap. A node lying on a member's line is not connected to it unless the member is split there. Two nodes at the same point are NOT merged: give each point one node, unless the two nodes are joined by a link (scissor joint, below). Every node must have a member, plate or support (a loose node is an error), except a diaphragm's separate retained node. - X-braces: either add a node where the two diagonals cross and split both (connected), or let them cross unconnected (a warning reminds you; fine for tension-only braces), or make a scissor joint: split each diagonal at its own node at the crossing (two nodes at the same point) and join them with link FFFRRR. The braces then move together at the crossing but pass no bending to each other. - Links: put supports and loads on the master node; the slave can't have a support in a direction it follows, nor settle=. - Give the structure enough supports to be stable in all three directions and against rotation. In 3D, pinned bases need bracing or moment connections elsewhere, and pinned supports all on one line let the structure rotate about that line. A 2D frame in the X-Y plane still needs restraint in Z: fix the bases, or hold dz (and rx, ry) at the supports. - Columns: draw them bottom to top. A vertical member drawn bottom to top has its web along global X, so an I-section column is strong against sway in X. Add roll=90 to turn the web along Z. (A column leaning more than 2% of its length is treated as a sloping member; see Member axes.) - Sections are upright unless you give a roll: an I-beam has its web vertical, a purlin or girt stands upright. roll= turns the section about its own axis in quarter turns only (0, 90, 180, 270), so purlins on a sloping roof stay vertical, not square to the roof. - Use "hinged" for simply supported beams (it releases bending, ry and rz, at both ends and keeps torsion). Do not hinge every member meeting at a node in a way that leaves that node free to spin, and do not release rotations at a member end whose node has no other member and no rotational support (it would spin). Never release rx (torsion) at both ends of a member (an error). - Haunches and tapers only when the engineer asks: an eaves haunch is haunch1= or haunch2= at the column end, about a tenth of the span long, adding about the rafter's depth. Lengths and depths in m (ft). - Semi-rigid ends (spring=) only when the engineer gives a joint stiffness; otherwise leave the end fixed, or use hinged / release=. - Pin-jointed trusses: keep the chords continuous and hinge the web members, so no node is left free to spin. Hinged webs add no out-of-plane restraint, so hold dz at the top-chord nodes (where purlins or bracing restrain them) or model that bracing. - Slabs and walls are plates: give the corner nodes (a 4-corner plate must be a true rectangle with square corners); the app meshes it. Put beams and columns along plate edges on the same corner nodes. - Each plate edge is split into 1, 2, 4, 8, 16, 32 or 64 equal elements (table under plate in section 3). The elements are exactly mesh= long only when edge / mesh= is one of those counts (8 m with mesh=0.5 gives 16 elements of 0.5 m; 6 m with mesh=0.5 also gives 16, of 0.375 m). A column under a slab, or a node for a point load on a slab, must sit on a mesh point (within 1 mm): a whole number of those element lengths from a corner along both edges. Beams may run inside a plate along a mesh line, but not inside a plate with openings (see below). Plates that share an edge need the same number of elements along it. - Openings go on their own lines, clear of columns and loaded nodes. The app refines the mesh around each opening (one opening can add several hundred elements), so use few, reasonably large openings. A plate with openings can't have a beam running inside it (the re-mesh around the openings has no mesh line for it, an error): split the plate along the beam into plates that meet there (beams along plate edges connect), and cut the openings in one of them. Loads and signs - Loads are in global axes unless axis=local is given. A global line load on a sloping member is per metre (or foot) of member length, not of plan. - An eccentric load (e.g. a pipe on a bracket) is the force plus its moment: 4 kN down, 0.3 m off a beam along X toward +Z is pointload P B1 at=1m fy=-4 mx=1.2 (right-hand rule: a downward force at +Z turns positively about +X). - Floor, wall and roof pressures: pressureload loads the framing members. One line can cover a whole flat floor or roof plane; list every member in it, including interior beams, purlins and joists, or they get none of the load. A member on the line between two surfaces (a ridge purlin) can be listed in both lines and takes load from each. Use pressure only on plates. A wall without members around it can't take a pressureload: load its columns with udl instead. - On a wall or roof, p may be negative for suction: pressureload W p=-0.6 dir=normal ... acts outward (uplift on a roof). On a wall, p > 0 pushes toward -X or -Z, whichever the wall faces more (a wall along X: toward -Z; a wall at 45 degrees in plan: also toward -Z). - Gravity acts in -Y: a downward point load is fy=-10, a downward line load is wy=-5, a downward plate pressure is pressure ... p=-3 dir=y. Exception: pressureload p is positive into the surface, so on a floor p=3 means 3 kPa down. - selfweight adds the weight of every member and plate from its section or thickness and material. - settle= moves a support by its full amount in every load case and every combination (factors don't scale it); use it only when asked for a settlement, and don't add a separate settlement case. - Imperial pressures are in ksf: 20 psf is p=0.02, not p=20. - Temperature gradients gy= and gz= are in deg C per metre of section depth (deg F per ft): a 30 deg C difference across a 0.3 m deep beam is gy=100. A plate's diff= is the full face-to-face difference: 10 deg C warmer on top is diff=10. - A slab with dt= held in its own plane all round (pinned or fixed edges) can't expand and takes large in-plane forces. For a slab free to expand, hold the edges vertically only (edge=...:roller on a floor) and stop it sliding and spinning in its plane at two or three corner nodes (e.g. one pinned, one support=dy,dz on the next corner along X). - Combinations list load case factors only, e.g. G=1.2 Q=1.5. Mark each one uls or sls so design checks treat it correctly. Write one combination per load arrangement; scripts have no automatic pattern loading or combination generator (the app has one after import). - Design settings (effective lengths, lateral restraints, design code) are not part of the script; the engineer sets them in the app after import. So are analysis options such as "Include member shear deformation" (Timoshenko members, for deep beams): a script imports with it off, and the engineer ticks it in the analysis dialog. - There are no loops or arrays: write every node and member. Scripts up to 1 MB are accepted. Common mistakes that are rejected - support=pin (write pinned), fx=10kN (no units: fx=10), x=3.5*2 (no arithmetic), lib="310UB40.4" (write UB_310x40_G300), spaces around = (write p=3), an id used before its own line, load case ids that differ only in letter case (G and g), and dir=normal on a floor pressureload. Before replying, check: every id used is defined on an earlier line, every member's two nodes differ, there are no duplicate ids, units is the first line, every lib= name follows section 5, and loads point the way the engineer described. ============================================================================ 3. FORMAT REFERENCE ============================================================================ Lines starting with # are comments. Blank lines are ignored. [ ] = optional. a|b = choose one. Options are written key=value, no spaces. units metric | imperial Required, first line. metric: coordinates m, plate thickness mm, force kN, moment kN-m, line load kN/m, pressure kPa, spring kN/m or kN-m/rad, temperature deg C, gradient deg C/m imperial: coordinates ft, plate thickness in, force kip, moment kip-ft, line load kip/ft, pressure ksf, spring kip/ft or kip-ft/rad, temperature deg F, gradient deg F/ft Units are for the numbers in the script only. Any library section or material can be used with either. name "Project name" description "Optional text" library The country whose section library lib= names on section lines are looked up in. Needed when a section uses lib= without country=. Countries: Australia, Brazil, Canada, China, Europe, India, Japan, New_Zealand, United_Kingdom, United_States. section ["Name"] [lib=""] [country=] lib= the library section, e.g. lib="UB_310x40_G300". Add folders in front when the same name is in more than one folder: lib="RHS_Rectangular_350/RHS_100x50x3". country= look this one section up in another country's library. Without lib= the section is a placeholder with that name: after import the engineer picks a library item or their own custom section for it (Sections dialog), and every member using it updates. material ["Name"] [lib=""] lib= the library material, with its folder path when the name is used more than once: lib="Australia/Steel/STEEL", lib="Metric/Steel/STEEL", lib="Imperial/Steel/STEEL". Without lib= the material is a placeholder picked after import (Materials dialog), from the library or the engineer's own materials. Library names match whole names only: letter case, ".json" and space versus underscore don't matter, nothing else is guessed. A name that matches no item, or more than one, is an error that lists what to write. Only items shown in the app's library can be named, up to 200 different items per script. The section is used as listed; the library sets its shape, properties and design data. Items are read from the library only for sections and materials that members or plates use. AXES AND SIGNS Global axes are right-handed with Y up. Node coordinates are global x y z, in m (ft). In the app's front view +X points right, +Y up and +Z out of the screen toward you; seen from above with +X to the right, +Z points down the page. Directions dx, dy, dz are movements along X, Y, Z; rx, ry, rz are rotations about X, Y, Z (supports, springs, settlement). release= uses rx, ry, rz about the member's own axes: rx torsion, rz bending in the member's x-y plane (vertical bending of an upright beam), ry bending in its x-z plane. Forces fx, fy, fz and line loads wx, wy, wz are positive along +X, +Y, +Z (or local +x, +y, +z with axis=local). Gravity is -Y. Moments mx, my, mz and rotations follow the right-hand rule: thumb along the positive axis, fingers curl in the positive direction (a positive mz turns anticlockwise in the front view). Settlement: settle=dy:-10 moves the support 10 mm down. Temperature: dt > 0 is warmer (the member expands); gy > 0 makes the local +y face hotter (the top face of an upright horizontal beam), gz > 0 the local +z face. On a plate, diff > 0 makes the face side hotter (a floor's top). Plate pressure p > 0 acts along the plate's face direction (see plate) or the positive global axis given by dir=; pressureload is the exception: p > 0 pushes into the surface, p < 0 pulls away from it. Results (reactions, member forces, plate stresses) follow the app's sign conventions: Documentation > Structural FEA > Sign Conventions. node [support=...] [spring=...] [settle=...] x y z: global coordinates in m (ft), Y up. support=fixed all six directions held support=pinned held in X, Y and Z, free to rotate support=roller held vertically (Y) only support=free nothing held (same as leaving support= out) support=FFFRRR six letters for DX DY DZ RX RY RZ, F = held, R = free support=dx,dy,dz list of held directions spring=dy:5000,rz:200 spring supports (direction:stiffness) settle=dy:-10 support settlement: the support moves by this much in every load case and every combination, at full value (combination factors don't scale it, as in the app; a separate settlement case adds nothing). Translations in mm (metric) or in (imperial), rotations in radians: settle=dy:-10,rz:0.002. Only on directions the support holds, and not on a node a diaphragm ties or on a link's slave (use the retained node or the master). member
[material=] [options] material= can be left out when only one material is declared hinged pinned at both ends (releases ry and rz, keeps torsion); "pinned" on a member line means the same release=start:rz | release=end:ry,rz | release=both:rz rotation releases at one or both ends, about the member's own axes (rx, ry, rz). Never rx at both ends. roll=0|90|180|270 Section rotation (roll): turns the section about its own axis (local x), in degrees from its default frame. 90 lays an I-beam with its web horizontal, 180 turns an angle, channel or tee upside down, 270 is 90 the other way. Only these four values. Leave it out for an upright section. behaviour=tension | compression tension-only or compression-only member (e.g. a brace). Leave it out for a normal member. ecc=x,y,z offset both ends (ecc1= start, ecc2= end only), in m (ft), the same units as coordinates eccaxis=local offsets in member axes instead of global axes The member end sits at node + offset; the gap is a rigid link. haunch=,[,bottom|top] haunches at both ends (haunch1= start, haunch2= end only): added at the member end, running out to nothing at . m (ft), like coordinates: haunch1=0.6,0.36 adds 360 mm over 600 mm at the start. is along the member (also on a sloping rafter), from its end (the offset end with ecc=); is added to the section depth, square to the member. bottom (default) or top face (local -y or +y; turns with roll=). taper=,[,both|top|bottom] web taper: overall depth runs linearly from depthA at the start to depthB at the end, m (ft); flanges as the section. Depths are square to the member. both (default) moves both faces; top or bottom slopes that face only, and the other face stays where the section's own face is. Haunches and taper: not both on one member; I-sections with parallel flanges or solid rectangles only; not with behaviour=. Design checks are not available for these members. spring=:,... semi-rigid ends instead of fixed, at both ends (spring1= start, spring2= end only). Directions in member axes, as release= (dx, dy, dz, rx, ry, rz); kN/m and kN-m/rad (kip/ft, kip-ft/rad). spring2=rz:20000 is a semi-rigid joint at the end. spring1= / spring2= replace spring= at their end (not added to it). A semi-rigid joint between two members (a beam splice, a continuous beam over a column) is a spring on one of them, the joint stiffness; the other stays fixed. Springs on both act one after the other (two of 15000 make 7500). A direction can't be both released and a spring (hinged with spring=rz is an error), but one end can mix them on different directions: spring1=rz:8000 release=start:ry. With behaviour=: no dy, dz or rx springs. Angles and Z sections: dy equal to dz, ry equal to rz. Member axes (for axis=local loads, eccaxis=local, release=, gy/gz and roll): local x runs from the start node to the end node; local y is the section's depth direction (along the web of an I-section); local z = x cross y. - Horizontal or sloping member: local y is perpendicular to it and points upward. A beam along +X: y = +Y, z = +Z. A beam along +Z: y = +Y, z = -X. - Vertical member drawn bottom to top (and any member leaning 2% of its length or less): y = -X, z = +Z. Drawn top to bottom: y = +X, z = +Z, so local y loads flip; draw columns bottom to top. - roll=90 turns the section +90 degrees about local x: the new local y is the old z and the new z is minus the old y. roll=90 beam along +X: y = +Z, z = -Y (axis=local wy acts along +Z). roll=90 beam along +Z: y = -X, z = -Y (a load toward +X is a negative wy). Releases, gy/gz and local offsets turn with it. - roll=180 turns y and z to -y and -z; roll=270 gives y = -(old z), z = +(old y). Releases, local loads, gy/gz and eccaxis=local offsets turn with every roll. - Writing a member end to start reverses local x. An asymmetric section (angle, channel, tee) then becomes its mirror image: there is no way to keep its handedness. Write members start to end unless you want the mirrored section. Check them in the app with Member Local Frame. plate [n4] thickness= [material=] [mesh=] [kx=..] [ky=..] [name="..."] [edge=-:,...] [hinge=-,...] A slab or wall from 3 or 4 corner nodes, in any order. A 4-corner plate must be a rectangle. It is meshed exactly like a plate drawn in the app: mesh= is the target element size (m or ft; default the app's, at most 0.5 m). Each edge gets equal elements, from edge length / mesh=: under 1.5 -> 1 1.5 to 2.5 -> 2 2.5 to 5.5 -> 4 5.5 to 11.5 -> 8 11.5 to 23.5 -> 16 23.5 to 47.5 -> 32 47.5 and over -> 64 (the most; longer edges get bigger elements) so 8 m at mesh=0.5 gives 16 and 6 m gives 16 (0.375 m). A triangle's count comes from its longest edge. Beams along an edge line up with the mesh. Plates that share an edge must get the same number of elements along it, so give neighbours a mesh= that does. Nodes that lie on the plate's mesh points (e.g. a column under a slab) are used by the mesh, a node elsewhere on the plate is an error; beams along plate edges are connected automatically. All plates together: at most 50,000 elements. Face direction (the sign of pressure p): the positive global axis closest to the plate's normal. Floors and roofs up to 45 degrees face up (+Y); steeper plates (walls) face +X or +Z, whichever they face more (a wall along X faces +Z), so a wall slightly out of plumb or skewed faces the same way as a true one. Pressure is applied to the plate area less its openings. p > 0 acts along the face direction: a wall along X faces +Z, so 5 kPa suction on its +Z face is p=5, water on its -Z side (pushing toward +Z) is also positive, and wind pushing on its +Z face is negative. Plate local axes (for kx/ky and opening w/h/rot): local x is global X projected onto the plate (global Z if the plate is within about 2.5 degrees of perpendicular to X); local z is the normal along the face direction; y = z cross x: floor or roof x = +X, y = -Z, z = +Y wall in the X-Y plane x = +X, y = +Y, z = +Z wall in the Y-Z plane x = +Z, y = -Y, z = +X An opening on a wall slightly out of plumb is placed as on a plumb one. kx/ky multiply the plate stiffness along local x/y (e.g. 0.5 for cracked concrete). edge= supports a whole edge, named by its two corner nodes, which must be next to each other in the plate's node list, in either order (plate P A B C D: edges A-B, B-C, C-D, D-A; A-C is not an edge): edge=A-B:pinned, edge=A-B:fixed,C-D:FFFRRR (fixed, pinned, roller, free or a six-letter code; not a list like dx,dy). Supports combine direction by direction: a direction held by the node's own support= or by the edge is held (a spring stays a spring). hinge= hinges whole edges, named the same way: hinge=A-B or hinge=A-B,C-D (no support after the edge). A hinged edge passes shear and in-plane force but no bending moment about the edge, e.g. a slab simply supported on a wall or beam. The hinge belongs to this plate; a plate on the other side stays continuous with what is there. An edge may have both edge= and hinge= (on a fixed edge the plate then turns freely about it). A plate held only along one straight hinged line is a mechanism; a hinge with nothing along it has no effect. opening circle d= at= opening rect w= h= at= [rot=] opening polygon points= A hole or edge notch in a plate. Positions are global coordinates on the plate (m or ft), within 10 mm of its plane; at= is the centre of a circle or rectangle. w runs along the plate's local x, h along its local y; rot turns the rectangle (degrees, -360 to 360) from local x toward local y, anticlockwise seen from the face direction: on a floor rot=90 puts w along Z, and rot=45 turns w from +X toward -Z. An opening clear of the plate edge is a hole; one that extends past the edge is an edge notch, cut from the plate (its new edges are free, and supports on the remaining edge stay). An opening must not just touch the edge, must stay clear of other openings and must have a real area; a node (corner or other) on the part a notch removes is an error. The plate is re-meshed around the hole by the app; nodes the plate used (column tops, supports, loaded nodes) stay in the new mesh, and a node inside an opening is an error. The re-mesh keeps those nodes but no mesh lines, so a beam running inside a plate with openings is an error: split the plate along the beam instead. The mesh is refined around the hole, so a small hole gives many small elements; keep openings few and not much smaller than mesh=. Two plates with openings can't share an edge. At most 50 openings per script; add more in the app. diaphragm ... [retained=] [normal=y|x|z] [mode=inplane|full] [name="..."] Ties the listed nodes together as a rigid floor. List every node in the floor (3 or more; fewer gets a warning). The retained node is the first listed, or retained=, which may also be a separate node not in the list (e.g. a node at the floor centre for a lateral load); a separate retained node needs no member and no support. Loads may go on any tied node or on the retained node. normal= is the floor's normal axis (y for a floor). mode=inplane (default) ties the in-plane movements and the rotation about the normal (for normal=y: dx, dz and ry) and leaves the floor free to bend; mode=full ties all six directions. All nodes must lie in one plane. A node can be in only one diaphragm, and a tied node can't have a support on a tied direction. link [name="..."] Ties the slave node to the master node in the directions the code gives. code: six letters F or R for DX DY DZ RX RY RZ in global axes (the same order as support=), F = the slave follows the master in that direction, R = free. At least one F. - Nodes at the same point: each F is a plain equality. FFFRRR joins two members as a pin (they move together and rotate freely), FFFFFF joins them rigidly. - Nodes apart: the link is a rigid arm. A tied translation follows the master's movement and its rotation over the gap, so FFFRRR at a distance is a rigid arm pinned at the slave: it carries the force and the moment of that force over the gap, and the slave turns freely. FFFFFF is a fully rigid arm. Put supports and loads on the master. The slave can't have a support in a direction it follows, nor settle=. Each direction of a node can follow only one master: one link per slave direction, and not a direction a diaphragm already ties. Links must not form a loop. Neither node may lie part-way along a member (split the member there). At a plate node, tie translations only (FFFRRR); a plate node can't be the master of a link whose nodes are apart. A master can have any number of slaves, one line each. Scissor joint (two braces crossing that move together but don't bend each other): split each brace at its own node at the crossing, then link L1 X Xb FFFRRR name="Scissor joint" (see the examples). case "Name" A load case. Loads below refer to it by id. selfweight [factor=1] nodeload [fx=..] [fy=..] [fz=..] [mx=..] [my=..] [mz=..] udl [wx=..] [wy=..] [wz=..] [from=..] [to=..] [axis=local] Line load along a member, full length by default. For a varying load add the end values: wy=-2 wy2=-6. pointload at=.. [fx=..] [fy=..] [fz=..] [mx=..] [my=..] [mz=..] [axis=local] Positions (at, from, to): 0.5 (fraction of length), 50%, or 2m / 6ft measured from the member's start node. A point load has no offset of its own: add the moment (see Loads and signs in section 2). With axis=local, forces and moments are along and about the member axes. pressure p=.. [p2=.. rise=x|y|z] [dir=normal|x|y|z] Pressure on a plate (kPa or ksf), positive along the plate's face direction (normal, the default) or along the positive global axis given: p=-3 dir=y is 3 kPa down. For a pressure that varies linearly, p is the value at the low end and p2 at the high end along global axis rise=, which must run along a plate edge; e.g. water on a wall: pressure H WALL p=20 p2=0 rise=y. A varying pressure needs at least 2 elements along rise= (use a smaller mesh=). pressureload p=.. members= [dist=twoway|oneway] [onto=x|y|z|horizontal|upslope] [dir=normal|x|y|z] [basis=surface|plan] A surface pressure (kPa or ksf) carried by the members around a floor, wall or roof, the same as the app's Pressure Load tool. members= lists every member in one flat surface: its boundary and any interior beams, purlins or joists (one line can cover a whole multi-bay floor; a member left out gets none of the load). Tension- or compression-only members are skipped. The surface is a floor if it tilts less than 1 degree, a wall if it is within about 6 degrees of vertical, and a slope otherwise. p is positive into the surface (negative for suction): down on a floor, toward -X / -Z on a wall facing +X / +Z (dir=x|y|z: positive toward -X / -Y / -Z). Floors are loaded vertically (no dir=); walls default to normal; sloping roofs default to dir=y, with basis=plan for a load given per plan area (snow, roof live load). Without basis=plan, p acts on the true (sloping) area, also for dir=x or dir=z. dist=oneway sends the load to one set of members: onto=x loads the members running along X; on walls and slopes onto=horizontal or onto=upslope. The members alone carry it, so don't also put the same load on a plate inside them. temperature [dt=..] [gy=..] [gz=..] [alpha=..] temperature [dt=..] [diff=..] [alpha=..] dt = uniform temperature change (deg C or F). Member: gy, gz = gradient across the member along its local y or z, in deg per m (ft) of depth, not the temperature difference: 30 deg C across a 0.3 m beam is gy=100. The gradient is used as given, whatever the depth of the section picked. Plate: diff = face side minus back side (face as for pressure: a floor's top, a wall's +X or +Z side), the full difference: a slab 10 deg C warmer on top is diff=10. Shrinkage: a negative dt. alpha = expansion coefficient per deg C (F); default the material's. combo ["Name"] = ... [uls|sls] e.g. combo ULS1 "1.2G + 1.5Q" G=1.2 Q=1.5 uls uls / sls sets the limit state design checks use the combination for. Without it the app infers it from the name (ULS, ultimate, strength, LRFD or ASD mean ULS; SLS or serviceability mean SLS), if it can. At most 100 load cases and 500 combinations. Not available in scripts: section or material properties, and your own custom sections and materials. Use a placeholder (leave lib= out) and pick them after import; the model can't be analysed until every placeholder that members or plates use has been picked. ============================================================================ 4. EXAMPLES ============================================================================ --- 2D portal frame (Australian sections) --- units metric library Australia name "Portal frame" section COL "Columns" lib="UC_310x97_G300" section RAF "Rafter" lib="UB_360x51_G300" material STEEL "Steel" lib="Australia/Steel/STEEL" node N1 0 0 0 support=fixed node N2 0 4 0 node N3 6 4 0 node N4 6 0 0 support=fixed member C1 N1 N2 COL # Eaves haunches at both ends: 600 mm long, adding 356 mm (the rafter depth). member R1 N2 N3 RAF haunch=0.6,0.356 # Columns are drawn bottom to top, so both have the same local axes. member C2 N4 N3 COL case G "Dead" case Q "Roof live" case W "Wind" selfweight G udl G R1 wy=-2 udl Q R1 wy=-1.5 nodeload W N2 fx=10 # AS/NZS 1170.0: roof live load is not combined with wind (psi c = 0). combo ULS1 "1.2G + 1.5Q" G=1.2 Q=1.5 uls combo ULS2 "1.2G + W" G=1.2 W=1 uls combo ULS3 "0.9G + W" G=0.9 W=1 uls combo SLS1 "G + 0.7Q" G=1 Q=0.7 sls --- 3D two-storey frame with floor loads (European sections) --- units metric library Europe name "Two-storey frame" # Europe lists each section under two steel grades, so the grade folder is named. section COL "Columns" lib="STEEL_Grade_355/HE_Beams/HE_200_B" section BM "Beams" lib="STEEL_Grade_355/IPE_Beams/IPE_300" section BR "Bracing" lib="STEEL_Grade_355/CHS_Circular/CHS_139.7x5" material STEEL "Steel" lib="Metric/Steel/STEEL" # Plan 6 m (X) by 5 m (Z). First floor at 3.5 m, roof at 7 m. node A0 0 0 0 support=fixed node B0 6 0 0 support=fixed node C0 6 0 5 support=fixed node D0 0 0 5 support=fixed node A1 0 3.5 0 node B1 6 3.5 0 node C1 6 3.5 5 node D1 0 3.5 5 node A2 0 7 0 node B2 6 7 0 node C2 6 7 5 node D2 0 7 5 # Columns, drawn bottom to top: webs along X, strong axis in the X frames. member CA1 A0 A1 COL member CB1 B0 B1 COL member CC1 C0 C1 COL member CD1 D0 D1 COL member CA2 A1 A2 COL member CB2 B1 B2 COL member CC2 C1 C2 COL member CD2 D1 D2 COL # X direction: moment frames on the z = 0 and z = 5 m lines (beams # continuous with the columns). member L1AB A1 B1 BM member L1CD C1 D1 BM member L2AB A2 B2 BM member L2CD C2 D2 BM # Z direction: simply supported beams, braced by one pin-ended diagonal per # storey in each end frame (x = 0 and x = 6 m). member L1BC B1 C1 BM hinged member L1DA D1 A1 BM hinged member L2BC B2 C2 BM hinged member L2DA D2 A2 BM hinged member BA1 A0 D1 BR hinged member BA2 A1 D2 BR hinged member BB1 B0 C1 BR hinged member BB2 B1 C2 BR hinged case G "Dead" case Q "Floor imposed" case R "Roof imposed" case W "Wind +X" selfweight G # Floor and roof pressures go to the beams around each level (members= lists them). pressureload G p=1.5 members=L1AB,L1BC,L1CD,L1DA pressureload G p=1 members=L2AB,L2BC,L2CD,L2DA pressureload Q p=3 members=L1AB,L1BC,L1CD,L1DA # Roof not accessible (category H, EN 1991-1-1 recommended 0.4 kPa). pressureload R p=0.4 members=L2AB,L2BC,L2CD,L2DA nodeload W A1 fx=5 nodeload W D1 fx=5 nodeload W A2 fx=3 nodeload W D2 fx=3 # EN 1990 eq. 6.10 with psi0 = 0.7 (offices), 0 (category H roofs) and # 0.6 (wind). Roof imposed load is not combined with wind (EN 1991-1-1 3.3.2). combo ULS1 "1.35G + 1.5Q" G=1.35 Q=1.5 uls combo ULS2 "1.35G + 1.5R + 1.05Q" G=1.35 R=1.5 Q=1.05 uls combo ULS3 "1.35G + 1.5W + 1.05Q" G=1.35 W=1.5 Q=1.05 uls combo ULS4 "1.35G + 1.5Q + 0.9W" G=1.35 Q=1.5 W=0.9 uls combo ULS5 "1.0G + 1.5W" G=1 W=1.5 uls combo SLS1 "G + Q" G=1 Q=1 sls --- Two-span beam, imperial (US sections) --- units imperial library United_States name "Two-span floor beam" section BM "Beam" lib="W_12x26" material STEEL "Steel" lib="Imperial/Steel/STEEL" # Two 20 ft spans. A holds the beam against sliding and twisting; # B and C hold it vertically and sideways. node A 0 0 0 support=dx,dy,dz,rx node B 20 0 0 support=dy,dz node C 40 0 0 support=dy,dz member B1 A B BM member B2 B C BM case D "Dead" case L "Live" selfweight D udl D B1 wy=-0.5 udl D B2 wy=-0.5 udl L B1 wy=-0.8 udl L B2 wy=-0.8 combo LRFD1 "1.2D + 1.6L" D=1.2 L=1.6 uls combo SLS1 "D + L" D=1 L=1 sls --- Flat slab with openings --- # A 220 mm flat slab on a 6 m column grid (2 x 2 bays, 12 m square), with # a stair void, a riser and a service void. The mesh is refined around each # opening. The slab is analysed on pinned point supports at the column # centrelines, the usual idealisation for flat slab design. The library has # no reinforced concrete column sections: to model the columns, add a # placeholder section (e.g. section COL "450x450 RC column") and pick a # custom section for it after import. units metric name "Flat slab with openings" material CONC "Concrete" lib="Australia/Concrete/CONCRETE_32" # Column grid at 6 m centres in X and Z; the slab is at 3.5 m. node A 0 3.5 0 support=pinned node B 6 3.5 0 support=pinned node C 12 3.5 0 support=pinned node D 0 3.5 6 support=pinned node E 6 3.5 6 support=pinned node F 12 3.5 6 support=pinned node G 0 3.5 12 support=pinned node H 6 3.5 12 support=pinned node I 12 3.5 12 support=pinned # mesh=0.6: each 12 m edge gets 16 elements of 0.75 m, so the supports at # 6 m sit on mesh points. plate SLAB A C I G thickness=220 material=CONC mesh=0.6 name="Level 1 slab" # Stair void, 2.4 m along X by 4.5 m along Z, in the middle of a corner panel. opening STAIR SLAB rect w=2.4 h=4.5 at=3,3.5,9 # Riser, 600 mm diameter, kept clear of the punching zone at column E. opening RISER SLAB circle d=0.6 at=7.8,3.5,4.2 # Service void, a 1.2 m triangle, mid-panel. opening VOID SLAB polygon points=8.4,3.5,8.4;9.6,3.5,8.4;9,3.5,9.6 case G "Dead" case Q "Live" selfweight G # Superimposed dead load and live load, downward (-Y). pressure G SLAB p=-1.5 dir=y pressure Q SLAB p=-3 dir=y combo ULS1 "1.2G + 1.5Q" G=1.2 Q=1.5 uls combo SLS1 "G + 0.7Q" G=1 Q=0.7 sls --- Section rotation and swap ends (angle, girts) --- units metric library Australia name "Section rotation" section POST "Posts" lib="UC_200x46_G300" section ANG "Edge angle" lib="EA_100x8" section GIRT "Girts" lib="PFC_150x75_G300" material STEEL "Steel" lib="Australia/Steel/STEEL" node A0 0 0 0 support=fixed node A1 0 1.2 0 node A2 0 2.4 0 node A3 0 3 0 node B0 5 0 0 support=fixed node B1 5 1.2 0 node B2 5 2.4 0 node B3 5 3 0 member PA1 A0 A1 POST member PA2 A1 A2 POST member PA3 A2 A3 POST member PB1 B0 B1 POST member PB2 B1 B2 POST member PB3 B2 B3 POST # roll=180 turns the edge angle upside down: both legs flip. member E1 A3 B3 ANG roll=180 hinged # roll=270 lays the channel on its side (web horizontal, depth along Z) for # wind on the wall. member G1 A1 B1 GIRT roll=270 hinged # G2 is written end to start. With roll=90 its web lies where G1's does, but # reversing a member mirrors an asymmetric section: its flanges point the # opposite way to G1's. member G2 B2 A2 GIRT roll=90 hinged case G "Dead" case W "Wind" selfweight G udl W G1 wz=-0.9 udl W G2 wz=-0.9 combo ULS1 "1.2G + W" G=1.2 W=1 uls combo SLS1 "G" G=1 sls --- Portal frame with a scissor X-brace (Australian sections) --- units metric library Australia name "Braced portal with scissor joint" section COL "Columns" lib="UC_310x97_G300" section RAF "Rafter" lib="UB_360x51_G300" section BR "Braces" lib="CHS_Circular_350/CHS_88.9x3.2" material STEEL "Steel" lib="Australia/Steel/STEEL" # 6 m wide and 4 m high in the X-Y plane; the fixed bases also hold the # frame out of its plane. node N1 0 0 0 support=fixed node N2 0 4 0 node N3 6 4 0 node N4 6 0 0 support=fixed # The diagonals cross at (3, 2). Each gets its own node there: X on the # N1-N3 diagonal, Xb on the N4-N2 diagonal. node X 3 2 0 node Xb 3 2 0 member C1 N1 N2 COL member R1 N2 N3 RAF member C2 N4 N3 COL # Each diagonal is continuous through its crossing node and pinned at the # frame. member D1 N1 X BR release=start:ry,rz member D2 X N3 BR release=end:ry,rz member D3 N4 Xb BR release=start:ry,rz member D4 Xb N2 BR release=end:ry,rz # Scissor joint: Xb follows X in DX, DY and DZ and turns freely, so the # braces move together at the crossing but pass no bending to each other. link L1 X Xb FFFRRR name="Scissor joint" case G "Dead" case W "Wind" selfweight G udl G R1 wy=-3 nodeload W N2 fx=12 combo ULS1 "1.2G + W" G=1.2 W=1 uls combo ULS2 "0.9G + W" G=0.9 W=1 uls combo SLS1 "G" G=1 sls --- Every script feature (reference building) --- # Uses every statement in the format on one building: two storeys, 8 m (X) # by 4 m (Z), floors at 4 m and 8 m. A braced steel frame with a concrete # roof slab (with a stair opening), a concrete wall retaining earth on the # x = 0 end (the building is cut into a slope there, and the level 1 floor # props the top of the wall), and a canopy on two posts off the x = 8 m end. units metric library Australia name "Script reference building" description "Two-storey braced steel frame with a concrete roof, retaining wall and canopy" # Library picks: Australian by default, one European section (country=), # a folder named where a size is in two grade folders, two materials. section COL "Columns" lib="UC_200x46_G300" section BM "Beams" lib="UB_310x40_G300" section GIRT "Girt" lib="PFC_150x75_G300" section BR "Braces and posts" lib="CHS_Circular_350/CHS_88.9x3.2" section CAN "Canopy beams" lib="STEEL_Grade_355/IPE_Beams/IPE_200" country=Europe material STEEL "Steel" lib="Australia/Steel/STEEL" material CONC "Concrete" lib="Australia/Concrete/CONCRETE_32" # Bases: a preset, a list of held directions plus a rotational spring # (semi-rigid base), a six-letter code with a 10 mm predicted settlement, # and rollers under the canopy posts (the posts carry vertical load only; # the main frame holds the canopy sideways). node A0 0 0 0 support=fixed node B0 8 0 0 support=dx,dy,dz spring=rz:5000 node C0 8 0 4 support=FFFRRR settle=dy:-10 node D0 0 0 4 support=fixed node E0 10 0 0 support=roller node F0 10 0 4 support=roller # Girt nodes half-way up the z = 0 face (the columns are split there). node AG 0 2 0 node BG 8 2 0 # Level 1 at 4 m with the canopy edge E1-F1; roof at 8 m. node A1 0 4 0 node B1 8 4 0 node C1 8 4 4 node D1 0 4 4 node E1 10 4 0 node F1 10 4 4 node A2 0 8 0 node B2 8 8 0 node C2 8 8 4 node D2 0 8 4 # Columns (material= is needed because two materials are declared). member CA1 A0 AG COL material=STEEL member CA2 AG A1 COL material=STEEL member CB1 B0 BG COL material=STEEL member CB2 BG B1 COL material=STEEL member CC1 C0 C1 COL material=STEEL member CD1 D0 D1 COL material=STEEL member CA3 A1 A2 COL material=STEEL member CB3 B1 B2 COL material=STEEL member CC3 C1 C2 COL material=STEEL member CD3 D1 D2 COL material=STEEL # Girt laid flat (roll=90), pinned, 180 mm outside the column line. member G1 AG BG GIRT material=STEEL roll=90 hinged ecc=0,0,-0.18 # Level 1: long beams continuous, a pinned end beam and a released one. # L1AB is haunched on its bottom face at both column connections: 300 mm # added at each end, running out over 600 mm. member L1AB A1 B1 BM material=STEEL haunch=0.6,0.3 # L1CD has semi-rigid ends of different stiffness (20000 kN-m/rad at C1, # 8000 at D1); at D1 it also turns freely about its minor axis. member L1CD C1 D1 BM material=STEEL spring1=rz:20000 spring2=rz:8000 release=end:ry member L1BC B1 C1 BM material=STEEL hinged member L1DA D1 A1 BM material=STEEL release=both:rz # Tension-only braces in the x = 8 m frame, one per storey; wind +Z # stretches both. member BR1 B0 C1 BR material=STEEL behaviour=tension hinged member BR2 B1 C2 BR material=STEEL behaviour=tension hinged # Canopy: beams 100 mm below level 1 (member axes) on two posts, tapered # on the bottom face from 300 mm deep at the frame to the IPE 200's depth. member CN1 B1 E1 CAN material=STEEL ecc=0,-0.1,0 eccaxis=local taper=0.3,0.2,bottom member CN2 C1 F1 CAN material=STEEL ecc=0,-0.1,0 eccaxis=local taper=0.3,0.2,bottom member CN3 E1 F1 CAN material=STEEL release=both:rz member P1 E0 E1 BR material=STEEL member P2 F0 F1 BR material=STEEL # Roof beams 230 mm below the slab centre (beam depth/2 + slab/2). member RAB A2 B2 BM material=STEEL ecc=0,-0.23,0 member RBC B2 C2 BM material=STEEL ecc=0,-0.23,0 member RCD C2 D2 BM material=STEEL ecc=0,-0.23,0 member RDA D2 A2 BM material=STEEL ecc=0,-0.23,0 # Plates are meshed like plates drawn in the app; mesh=0.5 splits the 8 m # and 4 m edges into 16 and 8 elements. The roof is cracked (kx/ky) and # has a stair opening; the wall is pinned along its base edge. The canopy # slab is hinged where it meets the frame (B1-C1): it passes no bending # moment into the level 1 edge beam. plate ROOF A2 B2 C2 D2 thickness=150 material=CONC mesh=0.5 kx=0.5 ky=0.5 name="Roof slab" opening STAIR ROOF rect w=2 h=1 at=2,8,2 plate WALL A0 D0 D1 A1 thickness=200 material=CONC mesh=0.5 edge=A0-D0:pinned name="End wall" plate CANOPY B1 E1 F1 C1 thickness=100 material=CONC mesh=0.5 hinge=B1-C1 name="Canopy" # Level 1 acts as a rigid floor in its own plane. diaphragm DF1 A1 B1 C1 D1 retained=A1 normal=y mode=inplane name="Level 1" # Scissor X-brace in the z = 4 m frame, ground storey: each diagonal has # its own node at the crossing (X1, X1b), is continuous through it and is # pinned at the frame; the link makes them move together there without # bending each other. node X1 4 2 4 node X1b 4 2 4 member BZ1 D0 X1 BR material=STEEL release=start:ry,rz member BZ2 X1 C1 BR material=STEEL release=end:ry,rz member BZ3 C0 X1b BR material=STEEL release=start:ry,rz member BZ4 X1b D1 BR material=STEEL release=end:ry,rz link L1 X1 X1b FFFRRR name="Scissor joint" case G "Dead" case Q "Live" case W "Wind +Z" case T "Temperature" case E "Earth pressure" selfweight G factor=1 # Level 1 floor pressures go to the framing beams (the app's pressure load # generator): two-way by default, or one-way onto the X-running beams. pressureload G p=1.2 members=L1AB,L1BC,L1CD,L1DA pressureload Q p=3 members=L1AB,L1BC,L1CD,L1DA dist=oneway onto=x # Plate pressures: global -Y on the roof and canopy. The wall faces +X; # 4 m of retained soil outside it pushes toward +X. At rest, propped: # K0 x gamma x h = 0.5 x 20 x 4 = 40 kPa at the base, 0 at the top. pressure G ROOF p=-1.5 dir=y pressure Q ROOF p=-1.5 dir=y pressure Q CANOPY p=-0.5 dir=y pressure E WALL p=40 p2=0 rise=y # Member loads: varying, partial in member axes, a point load with a # torque, and wind on the girt and the z = 0 face. udl G RAB wy=-1 wy2=-2 udl Q L1CD wy=-4 from=2m to=6m axis=local pointload G L1AB at=50% fy=-15 mx=1.5 pointload Q CN1 at=1m fy=-2 udl W G1 wz=1.5 nodeload W A1 fz=6 nodeload W B1 fz=6 nodeload W A2 fz=3 nodeload W B2 fz=3 # Roof beams: 20 deg C warmer, with a 10 deg C/m gradient through the depth. temperature T RAB dt=20 gy=10 temperature T RCD dt=20 gy=10 alpha=1.2e-5 # Roof slab in sun: 15 deg C warmer, its top 10 deg C warmer than its soffit. temperature T ROOF dt=15 diff=10 combo ULS1 "1.35G" G=1.35 uls combo ULS2 "1.2G + 1.5Q" G=1.2 Q=1.5 uls combo ULS3 "1.2G + 0.4Q + W" G=1.2 Q=0.4 W=1 uls combo ULS4 "0.9G + W" G=0.9 W=1 uls # Earth pressure as a variable action at 1.5; use the factor your code # requires for retained soil. combo ULS5 "1.2G + 1.5E" G=1.2 E=1.5 uls combo SLS1 "G + 0.7Q" G=1 Q=0.7 sls combo SLS2 "G + T" G=1 T=1 sls ============================================================================ 5. LIBRARY LIST ============================================================================ Every folder that lib= can name, with how many items it holds and three sample names: the first, middle and last in name order. For most steel folders that runs from small to large, but not always (e.g. HE_100_A ... HL_1100_R mixes series), so the samples show how names are written, not the size range. Names in between follow the same pattern. Names carry the main dimensions in the folder's units, in the order the section tables use. Common patterns: Australian UB_310x40 = depth (mm) x mass (kg/m), with _G250/_G300 for the grade; UK UB_457x191x106 = depth x width x mass; W_12x26 (US) = nominal depth (in) x weight (lb/ft); hollow sections SHS_90x2.5 / RHS_150x50x5 / CHS_60.3x3 = outside size(s) x wall thickness; US and Canadian imperial names write fractions with dashes (HSS_8x8x3-8 = 8 x 8 x 3/8 in, 1-1-2 = 1 1/2). Don't build a size from the pattern unless you are confident it exists: a name that doesn't exist is rejected with the closest names, or leave lib= out for the engineer to pick. Section folders are listed by country (the "library" line or country=); the folder path shown after the country is what you add in front of a name that is in more than one folder. Material folders are listed by full path. Australia ALUMINIUM/CH_Channels (43): CH_10x10x1.6, CH_40x20x2, ..., CH_176x76x11.1 ALUMINIUM/EA_Equal_Angles (35): EA_12x12x1.6, EA_50x50x1.6, ..., EA_101.6x101.6x9.53 ALUMINIUM/RET_Rectangular_Tubes (40): RET_38.1x17.45x3.18, RET_67x47x3, ..., RET_200x50x3 ALUMINIUM/RT_Round_Tubes (56): RT_10x1.2, RT_50x3, ..., RT_203.2x3 ALUMINIUM/SQT_Square_Tubes (43): SQT_12.7x1.6, SQT_45x2.5, ..., SQT_101.6x6.35 ALUMINIUM/TE_Tees (11): TE_20x20x1.6, TE_40x40x3, ..., TE_50x50x6x6 ALUMINIUM/UA_Unequal_Angles (47): UA_20x12x1.5, UA_70x20x1.6, ..., UA_200x100x8 STEEL/BT_Universal_Beam_Tees (32): BT_75x7, BT_205x30, ..., BT_380x122 STEEL/CH_Taper_flange_channels (3): CH_75x40, CH_100x50, CH_125x65 STEEL/CHS_Circular_250 (44): CHS_21.3x2.6, CHS_60.3x5.4, ..., CHS_610x12.7 STEEL/CHS_Circular_350 (89): CHS_13.5x2.3, CHS_127x6, ..., CHS_508x12.7 STEEL/EA_Equal_Angles (46): EA_25x3, EA_75x6, ..., EA_200x26 STEEL/FL_Flat_Bars (113): FL_20x3, FL_100x6, ..., FL_300x25 STEEL/PFC_Channels (17): PFC_75x40_G300, PFC_200x75_G300, ..., PFC_380x100_G300 STEEL/RB_Round_Bars (34): RB_10, RB_56, ..., RB_200 STEEL/RHS_Rectangular_350 (98): RHS_50x20x1.6, RHS_150x50x5, ..., RHS_400x300x16 STEEL/RHS_Rectangular_450 (101): RHS_50x20x1.6, RHS_125x75x3, ..., RHS_400x300x16 STEEL/SB_Square_Bars (7): SB_10x10, SB_20x20, ..., SB_40x40 STEEL/SHS_Square_350 (94): SHS_13x1.8, SHS_90x2.5, ..., SHS_400x16 STEEL/SHS_Square_450 (102): SHS_20x1.6, SHS_89x5, ..., SHS_400x16 STEEL/TFB_Taper_flange_beams (29): TFB_100x7.2_G300, TFB_254x37.2_G230, ..., TFB_610x149_G230 STEEL/UA_Unequal_Angles (19): UA_65x50x5, UA_125x75x6, ..., UA_150x100x12 STEEL/UB_Universal_Beams (56): UB_150x14_G250, UB_360x51_G250, ..., UB_760x244 STEEL/UBP_Bearing_Piles (10): UBP_200x122_G250, UBP_250x85_G300, ..., UBP_310x149 STEEL/UC_Universal_Columns (27): UC_100x15_G250, UC_200x60_G250, ..., UC_310x283 STEEL/WB_Welded_Beams (23): WB_700x115, WB_900x282, ..., WB_1200x455 STEEL/WC_Welded_Columns (18): WC_350x197, WC_400x328, ..., WC_500x440 STEEL_ColdFormed/CH_Duragal_Channels (12): CH_75x40x4, CH_200x75x6, ..., CH_300x90x8 STEEL_ColdFormed/L_B2B_C_Lysaght_Back_To_Back_Cees (16): L_B2B_C_10010, L_B2B_C_20015, ..., L_B2B_C_35030 STEEL_ColdFormed/L_B2B_SC_Lysaght_Back_To_Back_SupaCees (20): L_B2B_SC_15010, L_B2B_SC_25019, ..., L_B2B_SC_40032 STEEL_ColdFormed/L_C_Lysaght_Cees (17): L_C_10010, L_C_20015, ..., L_C_40030 STEEL_ColdFormed/L_PC_Lysaght_Plain_Channels (10): L_PC_05130, L_PC_09530, ..., L_PC_15230 STEEL_ColdFormed/L_SC_Lysaght_SupaCees (20): L_SC_15010, L_SC_25019, ..., L_SC_40032 STEEL_ColdFormed/L_SZ_Lysaght_SupaZeds (20): L_SZ_15010, L_SZ_25019, ..., L_SZ_40032 STEEL_ColdFormed/L_TH_Lysaght_Top_Hats (12): L_TH_4055, L_TH_9610, ..., L_TH_12090 STEEL_ColdFormed/L_Z_Lysaght_Zeds (16): L_Z_10010, L_Z_20015, ..., L_Z_35030 STEEL_ColdFormed/M_C_Metroll_Cees (19): M_C_10010, M_C_20019, ..., M_C_40030 STEEL_ColdFormed/M_Z_Metroll_Zeds (19): M_Z_10010, M_Z_20019, ..., M_Z_40030 STEEL_ColdFormed/S_B2B_C_Stramit_Back_To_Back_Cees (17): S_B2B_C_10010, S_B2B_C_15024, ..., S_B2B_C_35030 STEEL_ColdFormed/S_C_Stramit_Cees (17): S_C_100x10, S_C_150x24, ..., S_C_350x30 STEEL_ColdFormed/S_TH_Stramit_Top_Hats (6): S_TH_64075, S_TH_96075, ..., S_TH_96120 STEEL_ColdFormed/S_Z_Stramit_Zeds (17): S_Z_100x10, S_Z_150x24, ..., S_Z_350x30 TIMBER/CarterHolt_HyChord_LVL (5): HyChord_70x35, HyChord_115x35, ..., HyChord_150x35 TIMBER/CarterHolt_HyJoist_I-Beam (10): HJ_200x45, HJ_300x63, ..., HJ_400x90 TIMBER/CarterHolt_HySpan_LVL (47): Hyspan_90x35, Hyspan_190x35, ..., Hyspan_600x75 TIMBER/CarterHolt_Laser_Frame (11): LF_70x35, LF_140x35, ..., LF_290x45 TIMBER/E-Beam (37): e-beam_45x35, e-beam_240x45, ..., e-beam_600x75 TIMBER/Generic_Round_Timber (14): RT_D75, RT_D250, ..., RT_D600 TIMBER/Hyne_Beam_17 (63): Hyne17_130x45, Hyne17_330x85, ..., Hyne17_590x130 TIMBER/Hyne_Beam_18 (45): Hyne18_120x65, Hyne18_330x85, ..., Hyne18_600x130 TIMBER/Hyne_Beam_21 (52): Hyne21_120x40, Hyne21_300x65, ..., Hyne21_600x115 TIMBER/Hyne_Frame (4): Frame_70x35, Frame_90x35, ..., Frame_90x45 TIMBER/Hyne_LGL (12): LGL_130x44, LGL_245x44, ..., LGL_360x65 TIMBER/Hyne_LVL (14): LVL_95x45, LVL_200x63, ..., LVL_360x63 TIMBER/Seasoned_Timber (41): Seasoned_2_70x35, Seasoned_70x45, ..., Seasoned_290x45 TIMBER/Tilling_FrameSmart (10): FS_70x35, FS_140x45, ..., FS_290x45 TIMBER/Tilling_SmartFir (4): SF_150x50, SF_250x50, ..., SF_300x50 TIMBER/Tilling_SmartForm_LVL (5): SF_LVL_95x45, SF_LVL_150x45, ..., SF_LVL_150x75 TIMBER/Tilling_SmartFrame_LVL_15 (42): LVL15_90x35, LVL15_200x42, ..., LVL15_525x75 TIMBER/Tilling_SmartFrame_LVL_18 (19): LVL18_90x35, LVL18_190x45, ..., LVL18_360x65 TIMBER/Tilling_SmartJoist_I (19): SJ_200x44, SJ_300x68, ..., SJ_400x90 TIMBER/Tilling_SmartLam_GL13 (115): GL13_126x38, GL13_378x130, ..., GLC13_686x130 TIMBER/Tilling_SmartLam_GL17 (25): GL17_130x65, GL17_330x65, ..., GL17_590x85 TIMBER/Tilling_SmartLam_GL18 (100): GL18_90x45, GL18_350x115, ..., GL18_660x110 TIMBER/Unseasoned_Timber (63): Unseasoned_2_100x38, Unseasoned_225x38, ..., Unseasoned_300x300 Brazil STEEL/CHS_Circular (359): CHS_48.3x2, CHS_139.7x8, ..., CHS_339.7x16 STEEL/CS_Welded_Columns (122): CS_150x25, CS_450x209, ..., CS_650x593 STEEL/CVS_Welded_Beam_Columns (135): CVS_150x15, CVS_500x250, ..., CVS_1000x486 STEEL/HP_Bearing_Piles (8): HP_200x53.0, HP_310x79.0, ..., HP_310x125.0 STEEL/L_Equal_Angles (45): L_22x22x3.2, L_76x76x7.9, ..., L_203x203x25.4 STEEL/L_Unequal_Angles (30): L_89x64x6.4, L_127x89x12.7, ..., L_203x102x25.4 STEEL/RHS_Rectangular (191): RHS_50x30x2, RHS_120x80x2, ..., RHS_350x250x12.5 STEEL/SHS_Square (293): SHS_40x2, SHS_120x12.5, ..., SHS_260x16 STEEL/U_Channels (6): C_76x6.11, C_203x17.1, ..., C_305x30.7 STEEL/VS_Welded_Beams (168): VS_150x15, VS_700x122, ..., VS_2000x624 STEEL/VSM_Welded_Mono (50): VSM_200x18, VSM_450x49, ..., VSM_650x113 STEEL/W_Wide_Flange (62): W_150x13.0, W_310x117.0, ..., W_610x174.0 Canada ALUMINIUM/AC_AA_Standard_Channels (21): AC_2x0.577, AC_7x3.21, ..., AC_14x13.9 ALUMINIUM/AW_AA_Standard_W_Shapes (16): AW_3x1.64, AW_8x6.18, ..., AW_14x16.0 ALUMINIUM/C_American_Standard_Channels (36): C_2x1.22, C_8x4.25, ..., C_15x17.3 ALUMINIUM/EA_Equal_Angles (49): EA_1-1-2x1-1-2x1-4, EA_3x3x5-16, ..., EA_8x8x5-8 ALUMINIUM/EAS_Square_End_Equal_Angles (26): EAS_1-1-2x1-1-2x1-4, EAS_2-1-2x2-1-2x1-8, ..., EAS_4x4x1-8 ALUMINIUM/MC_Channels (27): MC_2.25x0.86, MC_5x3.11, ..., MC_12x10.3 ALUMINIUM/Pipe (94): Pipe_1-1-2xSch5, Pipe_3xSch40, ..., Pipe_12xSch80 ALUMINIUM/RET_Rectangular_Tubes (62): RET_1-1-2x1x1-8, RET_4x3x1-8, ..., RET_8x5x3-8 ALUMINIUM/RT_Round_Tubes (171): RT_1.5x0.25, RT_4.25x0.5, ..., RT_12x1 ALUMINIUM/S_American_Standard_I_Beams (23): S_3x1.96, S_8x6.35, ..., S_12x17.3 ALUMINIUM/SQT_Square_Tubes (50): SQT_1.5x0.25, SQT_3.5x0.125, ..., SQT_8x0.375 ALUMINIUM/TE_Tees (17): TE_1.00x2.00x0.421, TE_3.00x4.00x1.50, ..., TE_7.50x7.50x14.4 ALUMINIUM/UA_Unequal_Angles (67): UA_1-3-4x1-1-4x1-4, UA_3x2x3-8, ..., UA_8x6x11-16 ALUMINIUM/UAS_Square_End_Unequal_Angles (28): UAS_1-1-2x1-1-4x1-8, UAS_2x1x3-16, ..., UAS_5x4x1-8 ALUMINIUM/W_Shapes (26): W_3x2.16, W_8x6.12, ..., W_12x18.3 ALUMINIUM/Z_Zees (13): Z_1-3-4x1-3-4x1.09, Z_4-1-8x3-3-16x6.22, ..., Z_5x3-1-4x6.19 STEEL/CH_Channels (32): CH_75x5, CH_200x17, ..., CH_380x74 STEEL/CHS_Circular_ASTM (80): CHS_42x3.2, CHS_245x6.4, ..., CHS_711x25 STEEL/CHS_Circular_CSA (80): CHS_42x3.2, CHS_245x6.4, ..., CHS_711x25 STEEL/EA_Equal_Angles (66): EA_19x19x3.2, EA_89x89x13, ..., EA_203x203x29 STEEL/HP_Bearing_Piles (22): HP_200x54, HP_360x174, ..., HP_460x304 STEEL/MC_Channels (34): MC_150x17.9, MC_250x42.4, ..., MC_460x86 STEEL/RHS_Rectangular_ASTM (99): RHS_51x25x3.2, RHS_178x127x6.4, ..., RHS_610x305x25 STEEL/RHS_Rectangular_CSA (99): RHS_51x25x3.2, RHS_178x127x6.4, ..., RHS_610x305x25 STEEL/S_Standard_Beams (28): S_75x8, S_310x74, ..., S_610x180 STEEL/SHS_Square_ASTM (82): SHS_38x3.2, SHS_203x6.4, ..., SHS_559x25 STEEL/UA_Unequal_Angles (73): UA_51x38x3.2, UA_127x76x6.4, ..., UA_203x152x25 STEEL/W_Wide_Flange (281): W_100x19, W_460x315, ..., W_1100x499 STEEL/WRF_Welded_Reduced_Flange (15): WRF_1000x210, WRF_1400x348, ..., WRF_1800x543 STEEL/WT_Tees (188): WT_50x9.5, WT_180x231.5, ..., WT_460x223 STEEL/WWF_Welded_Wide_Flange (107): WWF_350x137, WWF_700x196, ..., WWF_2000x732 STEEL/WWT_Tees (41): WWT_175x68.5, WWT_225x124, ..., WWT_275x360.5 STEEL_ColdFormed/C_Purlins (85): 4CS2.5x059, 8CS2x070, ..., 12CS4x105 STEEL_ColdFormed/Canam_Cees (32): 152S70-144M, 229S89-326M, ..., 356S89-326M STEEL_ColdFormed/Canam_Zeds (32): 152Z76-144M, 229Z76-326M, ..., 356Z76-326M STEEL_ColdFormed/ExSteel_Cees (40): 06C10, 10C12, ..., 45C16 STEEL_ColdFormed/Nonstructural_Studs (50): 162S125-18, 400S125-18, ..., 800S125-68 STEEL_ColdFormed/Structural_Studs_Joists (241): 250S137-33, 600S250-54, ..., 1600S350-118 STEEL_ColdFormed/TopHats (10): 087F125-18, 150F125-18, ..., 150F125-43 STEEL_ColdFormed/Tracks (233): 162T125-18, 550T250-43, ..., 1600T250-118 STEEL_ColdFormed/Zed_Purlins (60): 3.5ZS1.5x059, 8ZS3.25x105, ..., 12ZS3.25x105 TIMBER/Generic_Round_Timber (14): RT_D75, RT_D250, ..., RT_D600 TIMBER/Glulam (247): G_80x114, G_265x988, ..., G_365x2128 TIMBER/Sawn_Lumber (18): SL_38x89, SL_64x184, ..., SL_89x286 TIMBER/Sawn_Timbers (21): ST_140x140, ST_191x394, ..., ST_394x394 China STEEL/C_Channels (41): C_5, C_25a, ..., C_40c STEEL/HM_Middle_Flange (15): HM148x100x6x9, HM440x300x11x18, ..., HM594x302x14x23 STEEL/HN_Narrow_Flange (59): HN100x50x5x7, HN550x200x10x16, ..., HN1008x302x21x40 STEEL/HT_Thin_Wall (27): HT95x48x3.2x4.5, HT168x88x3.2x4.5, ..., HT390x198x6x8 STEEL/HW_Wide_Flange (29): HW100x100x6x8, HW344x354x16x16, ..., HW502x470x20x25 STEEL/I_Beams (45): I_10, I_32b, ..., I_63c STEEL/L_Equal_Angles (115): L20x3, L90x10, ..., L250x35 STEEL/L_Unequal_Angles (71): L25x16x3, L100x63x8, ..., L200x125x18 STEEL/TM_Middle_Flange_Tees (15): TM74x100x6x9, TM220x300x11x18, ..., TM297x302x14x23 STEEL/TN_Narrow_Flange_Tees (46): TN50x50x5x7, TN248x199x9x14, ..., TN456x302x18x34 STEEL/TW_Wide_Flange_Tees (19): TW50x100x6x8, TW150x300x10x15, ..., TW214x407x20x35 Europe STEEL_ColdFormed/Ruukki_C_Purlins (27): LP-C100-1.0, LP-C200-2.0, ..., LP-C350-3.0 STEEL_ColdFormed/Ruukki_Z_Purlins (27): LP-Z100-1.0, LP-Z200-2.0, ..., LP-Z350-3.0 STEEL_Grade_235-275/CHS_Circular (892): CHS_17.2x1.5, CHS_83x3.2, ..., CHS_508x10 STEEL_Grade_235-275/EA_Equal_Angles (82): EA_20x20x3, EA_150x150x14, ..., EA_250x250x35 STEEL_Grade_235-275/HD_Columns (38): HD_260x54.1, HD_400x216, ..., HD_400x1086 STEEL_Grade_235-275/HE_Beams (152): HE_100_A, HE_600x337, ..., HL_1100_R STEEL_Grade_235-275/HP_Bearing_Piles (32): HP_200x43, HP_320x117, ..., HP_400x231 STEEL_Grade_235-275/IPE_Beams (53): IPE_80, IPE_A_160, ..., IPE_O_600 STEEL_Grade_235-275/IPN_Beams (21): IPN_80, IPN_280, ..., IPN_600 STEEL_Grade_235-275/RHS_Rectangular (1016): RHS_25x15x1.5, RHS_140x80x2, ..., RHS_500x300x16 STEEL_Grade_235-275/SHS_Square (279): SHS_20x20x1.5, SHS_125x125x10, ..., SHS_400x400x16 STEEL_Grade_235-275/UA_Unequal_Angles (19): UA_120x80x8, UA_150x90x10, ..., UA_200x100x14 STEEL_Grade_235-275/UAP_Channels (9): UAP_80x45, UAP_175x70, ..., UAP_300x100 STEEL_Grade_235-275/UPE_Channels (14): UPE_80x50, UPE_220x85, ..., UPE_400x115 STEEL_Grade_235-275/UPN_Channels (21): UPN_40x20, UPN_180x70, ..., UPN_400x110 STEEL_Grade_355/CHS_Circular (892): CHS_17.2x1.5, CHS_83x3.2, ..., CHS_508x10 STEEL_Grade_355/EA_Equal_Angles (82): EA_20x20x3, EA_150x150x14, ..., EA_250x250x35 STEEL_Grade_355/HD_Columns (38): HD_260x54.1, HD_400x216, ..., HD_400x1086 STEEL_Grade_355/HE_Beams (152): HE_100_A, HE_600x337, ..., HL_1100_R STEEL_Grade_355/HP_Bearing_Piles (32): HP_200x43, HP_320x117, ..., HP_400x231 STEEL_Grade_355/IPE_Beams (53): IPE_80, IPE_A_160, ..., IPE_O_600 STEEL_Grade_355/IPN_Beams (21): IPN_80, IPN_280, ..., IPN_600 STEEL_Grade_355/RHS_Rectangular (1016): RHS_25x15x1.5, RHS_140x80x2, ..., RHS_500x300x16 STEEL_Grade_355/SHS_Square (279): SHS_20x20x1.5, SHS_125x125x10, ..., SHS_400x400x16 STEEL_Grade_355/UA_Unequal_Angles (19): UA_120x80x8, UA_150x90x10, ..., UA_200x100x14 STEEL_Grade_355/UAP_Channels (9): UAP_80x45, UAP_175x70, ..., UAP_300x100 STEEL_Grade_355/UPE_Channels (14): UPE_80x50, UPE_220x85, ..., UPE_400x115 STEEL_Grade_355/UPN_Channels (21): UPN_40x20, UPN_180x70, ..., UPN_400x110 TIMBER/Generic_Round_Timber (14): RT_D75, RT_D250, ..., RT_D600 TIMBER/Glulam_EN14080 (148): G_60x120, G_140x560, ..., G_240x720 TIMBER/Kerto_LVL (80): LVL_27x200, LVL_51x200, ..., LVL_75x600 TIMBER/KVH_Structural (23): KVH_60x100, KVH_80x200, ..., KVH_140x140 TIMBER/Sawn_Lumber_EN336 (39): SL_45x70, SL_95x120, ..., SL_145x295 India STEEL/CHS_Circular (84): CHS_21.3x2, CHS_165.1x5.4, ..., CHS_355.6x12 STEEL/ISA_Equal_Angles (91): ISA_20x20x3, ISA_70x70x10, ..., ISA_200x200x25 STEEL/ISA_Unequal_Angles (107): ISA_30x20x3, ISA_80x60x7, ..., ISA_200x150x20 STEEL/ISHB_Heavy_Beams_Columns (17): ISHB_150, ISHB_250a, ..., ISHB_450a STEEL/ISJB_Junior_Beams (4): ISJB_150, ISJB_200, ..., ISJB_225 STEEL/ISJC_Junior_Channels (5): ISJC_100, ISJC_150, ..., ISJC_200 STEEL/ISLB_Light_Weight_Beams (21): ISLB_75, ISLB_325, ..., ISLB_P_300 STEEL/ISLC_Light_Channels (15): ISLC_75, ISLC_250, ..., ISLC_P_300 STEEL/ISMB_Medium_Flange_Beams (14): ISMB_100, ISMB_300, ..., ISMB_600 STEEL/ISMC_Medium_Channels (20): ISMC_75, ISMC_225, ..., ISMC_400 STEEL/ISNPB_Narrow_Parallel_Flange_Beams (70): ISNPB_100x55x8.1, ISNPB_300x165x53.46, ..., ISNPB_750x270x202.49 STEEL/ISPBP_Bearing_Piles (29): ISPBP_200x43.85, ISPBP_320x88.48, ..., ISPBP_400x230.9 STEEL/ISPFC_Parallel_Flange_Channels (20): ISMPC_75, ISMPC_225, ..., ISMPC_400 STEEL/ISSC_Standard_Columns (9): ISSC_100, ISSC_160, ..., ISSC_250 STEEL/ISWB_Wide_Flange_Beams (14): ISWB_150, ISWB_350, ..., ISWB_600x145.06 STEEL/ISWPB_Wide_Parallel_Flange_Beams (122): ISWPB_100x100x12.24, ISWPB_320x300x74.25, ..., ISWPB_900x300x291.46 STEEL/RHS_Rectangular (59): RHS_50x25x2, RHS_127x50x3.6, ..., RHS_300x200x12 STEEL/SHS_Square (82): SHS_25x2, SHS_75x3.2, ..., SHS_250x12 STEEL_ColdFormed/Cee_Lipped_Rectangular (68): C_30x15x10x1.6, C_100x25x25x4, ..., C_250x80x25x5 STEEL_ColdFormed/Cee_Lipped_Square (20): C_25x25x8x1.6, C_60x60x15x2, ..., C_100x100x25x5 STEEL_ColdFormed/Equal_Angles_CF (26): EA_20x20x1.25, EA_60x60x3.15, ..., EA_100x100x6 STEEL_ColdFormed/PlainChannel_Rectangular (86): PC_30x15x1.6, PC_80x60x2, ..., PC_250x80x5 STEEL_ColdFormed/PlainChannel_Square (28): PC_20x20x1.6, PC_50x50x2.55, ..., PC_100x100x6 STEEL_ColdFormed/TopHat_Narrow (13): H_50x40x20x3.15, H_80x50x15x2, ..., H_100x80x15x2 STEEL_ColdFormed/TopHat_Square (21): H_30x30x10x1.6, H_60x60x20x3.15, ..., H_100x100x30x6 STEEL_ColdFormed/TopHat_Wide (4): H_30x50x10x1.6, H_40x60x15x2, ..., H_40x60x20x3.15 STEEL_ColdFormed/Unequal_Angles_CF (22): UA_20x15x1.6, UA_40x25x2, ..., UA_100x50x5 STEEL_ColdFormed/Zed_Lipped (135): Z_80x40x20x1.6, Z_170x60x20x2.3, ..., Z_300x75x20x3.15 Japan STEEL/C_Channels (10): C_75x40x5x7, C_180x75x7x10.5, ..., C_300x90x9x13 STEEL/CHS_Circular (127): CHS_21.7x2, CHS_165.2x4, ..., CHS_508x16 STEEL/H_Shapes (85): H_100x100x6x8, H_390x300x10x16, ..., H_918x303x19x37 STEEL/L_Equal_Angles (79): L_20x20x3, L_80x80x6, ..., L_250x250x35 STEEL/L_Unequal_Angles (6): L_100x75x7, L_125x75x10, ..., L_150x90x12 STEEL/RHS_Rectangular (239): RHS_60x30x1.6, RHS_150x100x4.5, ..., RHS_600x300x22 STEEL/SHS_Square (169): SHS_50x1.6, SHS_125x9, ..., SHS_550x22 STEEL/T_Structural_Tees (85): T_50x100x6x8, T_195x300x10x16, ..., T_459x303x19x37 STEEL_ColdFormed/C_Light_Channels (65): LightC_40x20x1.6, LightC_250x50x6, ..., LightC_450x75x6 STEEL_ColdFormed/C_Lip_Channels (44): LipC_60x30x10x1.6, LipC_150x65x20x3.2, ..., LipC_250x75x25x4.5 New_Zealand TIMBER/Dried_Framing_NZS3604 (23): Dried_70x35, Dried_190x35, ..., Dried_290x90 TIMBER/Generic_Round_Timber (14): RT_D75, RT_D250, ..., RT_D600 TIMBER/Green_Gauged_Framing_NZS3604 (23): Green_69x37, Green_194x37, ..., Green_294x94 United_Kingdom STEEL/CH_Channels (16): CH_100x50x10, CH_230x75x26, ..., CH_430x100x64 STEEL/CHS_Circular (163): CHS_21.3x3.2, CHS_244.5x6, ..., CHS_660x50 STEEL/EA_Equal_Angles (50): EA_25x3, EA_70x10, ..., EA_200x24 STEEL/MAC_Macalloy_Tension_Bars (21): MAC_M10, MAC_M64, ..., MAC_M120 STEEL/PFC_Channels (16): PFC_100x50x10, PFC_230x75x26, ..., PFC_430x100x64 STEEL/RHS_Rectangular (125): RHS_50x30x2.5, RHS_120x80x5, ..., RHS_500x300x20 STEEL/SHS_Square (161): SHS_40x2.5, SHS_160x16, ..., SHS_700x40 STEEL/UA_Unequal_Angles (32): UA_40x25x4, UA_100x75x12, ..., UA_200x150x18 STEEL/UB_Universal_Beams (90): UB_127x76x13, UB_457x191x106, ..., UB_1016x305x584 STEEL/UBP_Bearing_Piles (17): UBP_203x203x45, UBP_305x305x110, ..., UBP_356x368x174 STEEL/UBT_Universal_Beam_Tees (62): UBT_102x127x11, UBT_178x203x37, ..., UBT_305x457x127 STEEL/UC_Universal_Columns (51): UC_152x152x23, UC_305x305x137, ..., UC_356x406x1299 STEEL/UCT_Universal_Column_Tees (23): UCT_133x102x13, UCT_254x127x45, ..., UCT_406x178x118 TIMBER/CLS_Timber (7): CLS_38x63, CLS_38x140, ..., CLS_38x285 TIMBER/Generic_Round_Timber (14): RT_D75, RT_D250, ..., RT_D600 TIMBER/Glulam_EN14080 (148): G_60x120, G_140x560, ..., G_240x720 TIMBER/Kerto_LVL (80): LVL_27x200, LVL_51x200, ..., LVL_75x600 TIMBER/Sawn_Lumber_EN336 (70): SL_35x75, SL_47x295, ..., SL_100x295 United_States ALUMINIUM/AC_AA_Standard_Channels (21): AC_2x0.577, AC_7x3.21, ..., AC_14x13.9 ALUMINIUM/AW_AA_Standard_W_Shapes (16): AW_3x1.64, AW_8x6.18, ..., AW_14x16.0 ALUMINIUM/C_American_Standard_Channels (36): C_2x1.22, C_8x4.25, ..., C_15x17.3 ALUMINIUM/EA_Equal_Angles (49): EA_1-1-2x1-1-2x1-4, EA_3x3x5-16, ..., EA_8x8x5-8 ALUMINIUM/EAS_Square_End_Equal_Angles (26): EAS_1-1-2x1-1-2x1-4, EAS_2-1-2x2-1-2x1-8, ..., EAS_4x4x1-8 ALUMINIUM/MC_Channels (27): MC_2.25x0.86, MC_5x3.11, ..., MC_12x10.3 ALUMINIUM/Pipe (94): Pipe_1-1-2xSch5, Pipe_3xSch40, ..., Pipe_12xSch80 ALUMINIUM/RET_Rectangular_Tubes (62): RET_1-1-2x1x1-8, RET_4x3x1-8, ..., RET_8x5x3-8 ALUMINIUM/RT_Round_Tubes (171): RT_1.5x0.25, RT_4.25x0.5, ..., RT_12x1 ALUMINIUM/S_American_Standard_I_Beams (23): S_3x1.96, S_8x6.35, ..., S_12x17.3 ALUMINIUM/SQT_Square_Tubes (50): SQT_1.5x0.25, SQT_3.5x0.125, ..., SQT_8x0.375 ALUMINIUM/TE_Tees (17): TE_1.00x2.00x0.421, TE_3.00x4.00x1.50, ..., TE_7.50x7.50x14.4 ALUMINIUM/UA_Unequal_Angles (67): UA_1-3-4x1-1-4x1-4, UA_3x2x3-8, ..., UA_8x6x11-16 ALUMINIUM/UAS_Square_End_Unequal_Angles (28): UAS_1-1-2x1-1-4x1-8, UAS_2x1x3-16, ..., UAS_5x4x1-8 ALUMINIUM/W_Shapes (26): W_3x2.16, W_8x6.12, ..., W_12x18.3 ALUMINIUM/Z_Zees (13): Z_1-3-4x1-3-4x1.09, Z_4-1-8x3-3-16x6.22, ..., Z_5x3-1-4x6.19 STEEL/2L_Equal_Double_Angles (183): 2L_2-1-2x2-1-2x1-2, 2L_5x5x3-8x3-4, ..., 2L_12x12x1x3-4 STEEL/2L_Unequal_Double_Angles (456): 2L_2-1-2x1-1-2x1-4LLBB, 2L_5x3-1-2x3-8LLBB, ..., 2L_8x6x9-16x3-8SLBB STEEL/CH_Channels (32): CH_3x3.5, CH_8x11.5, ..., CH_15x50 STEEL/EA_Equal_Angles (61): EA_2-1-2x2-1-2x1-2, EA_5x5x3-8, ..., EA_12x12x1-3-8 STEEL/HP_Shapes (22): HP_8x36, HP_14x117, ..., HP_18x204 STEEL/HSS_Rectangular (399): HSS_2-1-2x1-1-2x1-4, HSS_12x3x5-16, ..., HSS_34x10x7-8 STEEL/HSS_Round (189): HSS_1.660x0.140, HSS_9.625x0.250, ..., HSS_28.000x1.000 STEEL/HSS_Square (126): HSS_1-1-2x1-1-2x1-4, HSS_8x8x3-8, ..., HSS_22x22x7-8 STEEL/M_Shapes (16): M_3x2.9, M_10x7.5, ..., M_12x11.8 STEEL/MC_Shapes (40): MC_3x7.1, MC_10x22, ..., MC_18x58 STEEL/MT_Shapes (14): MT_2.5x9.45, MT_5x4, ..., MT_6x5.9 STEEL/Pipe (51): Pipe_1-1-2STD, Pipe_5xS, ..., Pipe_26xS STEEL/S_Shapes (28): S_3x5.7, S_12x50, ..., S_24x121 STEEL/ST_Shapes (28): ST_1.5x2.85, ST_6x25, ..., ST_12x60.5 STEEL/UA_Unequal_Angles (76): UA_2-1-2x1-1-2x1-4, UA_5x3-1-2x3-8, ..., UA_8x6x9-16 STEEL/W_Shapes (289): W_4x13, W_21x50, ..., W_44x408 STEEL/WT_Shapes (289): WT_2.5x8, WT_10.5x25, ..., WT_22x204 STEEL_ColdFormed/C_Purlins (85): 4CS2.5x059, 8CS2x070, ..., 12CS4x105 STEEL_ColdFormed/Nonstructural_Studs (50): 162S125-18, 400S125-18, ..., 800S125-68 STEEL_ColdFormed/Structural_Studs_Joists (241): 250S137-33, 600S250-54, ..., 1600S350-118 STEEL_ColdFormed/TopHats (10): 087F125-18, 150F125-18, ..., 150F125-43 STEEL_ColdFormed/Tracks (233): 162T125-18, 550T250-43, ..., 1600T250-118 STEEL_ColdFormed/Zed_Purlins (60): 3.5ZS1.5x059, 8ZS3.25x105, ..., 12ZS3.25x105 TIMBER/Generic_Round_Timber (11): RT_4in, RT_12in, ..., RT_24in TIMBER/Glulam_Southern_Pine (255): GSP_2.5x5.5, GSP_5x19.25, ..., GSP_10.5x60.5 TIMBER/Glulam_Western_Species (231): GWS_2.5x6, GWS_6.75x37.5, ..., GWS_12.25x60 TIMBER/Sawn_Beams_Stringers (36): BS_6x10, BS_10x20, ..., BS_20x24 TIMBER/Sawn_Lumber (24): SL_2x3, SL_3x10, ..., SL_4x16 TIMBER/Sawn_Posts_Timbers (20): PT_5x5, PT_14x16, ..., PT_24x24 Materials (lib= on a material line) Imperial/Aluminium (1): ALUMINIUM Imperial/Concrete (14): CONCRETE_3000, CONCRETE_4500, ..., CONCRETE_10000 Imperial/Stainless_Steel (2): STAINLESS_STEEL, STAINLESS_STEEL_DUPLEX Imperial/Steel (1): STEEL Imperial/Timber_NDS_2018/Beams_and_Stringers (105): Alaska Cedar - No.1, Mountain Hemlock - No.2, ..., White Oak - Select Structural Imperial/Timber_NDS_2018/Decking (136): Balsam Fir - Commercial Repetitive, Redwood - Commercial, ..., Western Woods - Selected Repetitive Imperial/Timber_NDS_2018/Dimension_Lumber (330): Alaska Cedar - Construction, Northern Red Oak - Select Structural, ..., Yellow Poplar - Utility Imperial/Timber_NDS_2018/Hardwood_Glulam_Axial (37): Hardwood Group A - 1.5E3 H17, Hardwood Group C - 1.5E3 H27, ..., Hardwood Group D - Ss H16 Imperial/Timber_NDS_2018/Hardwood_Glulam_Bending (21): E Rated Hardwoods - 16F E1, Visually Graded Hardwoods - 12F V2, ..., Visually Graded Hardwoods - 20F V2 Imperial/Timber_NDS_2018/Mechanically_Graded_Dimension_Lumber (315): Douglas Fir-Larch - 900F-1.0E, Southern Pine - 975F-1.6E, ..., Western Woods - 2850F-2.3E Imperial/Timber_NDS_2018/Non_North_American_Dimension_Lumber (144): Austrian Spruce Austria and Czech Republic - Construction, Norway Spruce Sweden - Construction, ..., Southern Pine Misiones Argentina Free Of Heart Center and Medium Grain Density - Utility Imperial/Timber_NDS_2018/Posts_and_Timbers (105): Alaska Cedar - No.1, Mountain Hemlock - No.2, ..., White Oak - Select Structural Imperial/Timber_NDS_2018/Round_Timber_Pile (3): Pacific Coast Douglas Fir - ASTM D25, Red Pine - ASTM D25, Southern Pine Grouped - ASTM D25 Imperial/Timber_NDS_2018/Round_Timber_Pole (8): Lodgepole Pine - ASTM D3200, Southern Pine Grouped - ASTM D3200, ..., Western Red Cedar - ASTM D3200 Imperial/Timber_NDS_2018/Softwood_Glulam_Axial (30): AC - L1d 71, POC - L3 73, ..., SW - L3 22 5 Imperial/Timber_NDS_2018/Softwood_Glulam_Bending (12): 16F-1.3E DF-DF, 24F-1.8E DF-DF, ..., 30F-2.1E SP-SP Imperial/Timber_NDS_2018/Timbers_5x5_and_Larger (18): Baldcypress - No.1, Southern Pine - Dense Select Structural, ..., Southern Pine - Select Structural Metric/Aluminium (1): ALUMINIUM Metric/Australia/Aluminium (1): ALUMINIUM Metric/Australia/Concrete (8): CONCRETE_20, CONCRETE_50, ..., CONCRETE_100 Metric/Australia/Stainless_Steel (3): STAINLESS_STEEL, STAINLESS_STEEL_DUPLEX, STAINLESS_STEEL_FERRITIC Metric/Australia/Steel (1): STEEL Metric/Australia/Timber_Engineered (9): A17, SMART_FIR_F8, ..., SMART_GL18 Metric/Australia/Timber_F_Grades (1010): F4_ASH_ALPINE_S, F14_ASH_ALPINE_S, ..., F34_WANDOO_U Metric/Australia/Timber_GL_Grades (6): GL8_GENERIC_AS1720, GL13_GENERIC_AS1720, ..., GL18_GENERIC_AS1720 Metric/Australia/Timber_LVL (5): E-BEAM_LVL, HYSPAN_LVL, ..., SMART_LVL_18 Metric/Australia/Timber_MGP (3): MGP_10, MGP_12, MGP_15 Metric/Brazil/Steel (1): STEEL Metric/Canada/Aluminium (1): ALUMINIUM Metric/Canada/Concrete (14): CONCRETE_20, CONCRETE_50, ..., CONCRETE_80 Metric/Canada/Steel (1): STEEL Metric/Canada/Timber_CSA_O86-19/Timber_Glulam (12): DFIR_GLULAM_16c-E, HEMFIR_DFIR_GLULAM_24f-E, ..., SPF_GLULAM_20f-EX Metric/Canada/Timber_CSA_O86-19/Timber_Light_Framing (8): DOUGLAS_FIR_LARCH_LIGHT_FRAMING_CONSTRUCTION, NORTHERN_LIGHT_FRAMING_CONSTRUCTION, ..., SPRUCE_PINE_FIR_LIGHT_FRAMING_STANDARD Metric/Canada/Timber_CSA_O86-19/Timber_MEL (56): DOUGLAS_FIR_LARCH_MEL_M10, NORTHERN_MEL_M10, ..., SPRUCE_PINE_FIR_MEL_M26 Metric/Canada/Timber_CSA_O86-19/Timber_MSR (88): DOUGLAS_FIR_LARCH_MSR_1200Fb_1.2E, NORTHERN_MSR_1200Fb_1.2E, ..., SPRUCE_PINE_FIR_MSR_3000Fb_2.4E Metric/Canada/Timber_CSA_O86-19/Timber_Sawn (36): DOUGLAS_FIR_LARCH_BEAM_STRINGER_NO1, NORTHERN_BEAM_STRINGER_NO1, ..., SPRUCE_PINE_FIR_POST_TIMBER_SS Metric/China/Concrete (14): C15, C50, ..., C80 Metric/China/Steel (1): STEEL Metric/Europe/Aluminium (1): ALUMINIUM Metric/Europe/Concrete (14): C12_15, C45_55, ..., C90_105 Metric/Europe/Stainless_Steel (3): STAINLESS_STEEL_AUSTENITIC, STAINLESS_STEEL_DUPLEX, STAINLESS_STEEL_FERRITIC Metric/Europe/Steel (1): STEEL Metric/Europe/Timber/Timber_Glulam (14): GL20c, GL26h, ..., GL32h Metric/Europe/Timber/Timber_Hardwood (14): D18, D50, ..., D80 Metric/Europe/Timber/Timber_KVH (1): KVH_C24 Metric/Europe/Timber/Timber_LVL (8): Kerto_L_panel_21_24, Kerto_Qp_beam_39_51, ..., Kerto_T_stud Metric/Europe/Timber/Timber_Sawn (12): C14, C27, ..., C50 Metric/Europe/Timber/Timber_Tension (18): T8, T16, ..., T30 Metric/India/Concrete (15): M10, M45, ..., M80 Metric/India/Steel (1): STEEL Metric/Japan/Steel (1): STEEL Metric/New_Zealand/Concrete (13): CONCRETE_25, CONCRETE_55, ..., CONCRETE_100 Metric/New_Zealand/Steel (1): STEEL Metric/New_Zealand/Timber_NZS3603/Timber_Machine_Stress_Graded (10): DOUGLAS_FIR_MSG6_DRY, RADIATA_PINE_MSG6_DRY, ..., RADIATA_PINE_MSG15_DRY Metric/New_Zealand/Timber_NZS3603/Timber_Round (2): ROUND_SOFTWOOD_HIGH_GREEN, ROUND_SOFTWOOD_NORMAL_GREEN Metric/New_Zealand/Timber_NZS3603/Timber_Visually_Graded (10): DOUGLAS_FIR_G8_GREEN, RADIATA_PINE_G8_GREEN, ..., RADIATA_PINE_VSG10_DRY Metric/Stainless_Steel (1): STAINLESS_STEEL Metric/Steel (1): STEEL