Skip to main content

Elastic Critical Moment (Mcr) Calculator for Eurocode 3

Calculate Mcr, the elastic critical moment for lateral-torsional buckling that EN 1993-1-1 clause 6.3.2.2 asks for but gives no formula for, by buckling analysis of the beam. Any combination of end moments, uniform load and point loads, loads on the top or bottom flange, intermediate restraints, cantilevers and unequal flanges. Pick a section from the library, type its catalogue properties or enter the plates of a welded I-section. Free, no signup required.

Elastic Critical Moment Calculator

Section

Doubly symmetric I-section from the section tables. The defaults are an IPE 300.

Beam

Both ends are held against lateral movement and twist. In the plane of loading the beam is simply supported; end moments represent continuity.

Loading

Loads are positive downward and moments positive sagging. Only the shape of the loading matters: Mcr does not depend on its magnitude.

Intermediate restraints

Results

Elastic critical moment
Mcr = 102.3 kN·m
Load factor at buckling
2.27
Ratio to uniform moment
1.131

Mcr is the critical value of the largest moment in the beam, 45.00 kN·m sagging at 3.00 m under the entered loading. The ratio compares it with 90.5 kN·m, the value for the same length on fork supports under uniform moment and without intermediate restraints.

Bending moment, entered loading45.00 kN·mBuckled shape in plan (lateral movement of each flange, scaled)Top flangeBottom flange

Structural FEA

3D FEA with Eurocode 3 design checks

This page checks one beam. In Structural FEA you model the whole frame in 3D, and every steel member is checked to EN 1993-1-1 under every load combination: section classification, bending, shear, axial force, flexural buckling, lateral-torsional buckling and combined actions, each with the moment diagram from the analysis rather than one you have to enter.

3D frames and plates · Load combinations · Eurocode 3, AISC 360, AS 4100 and CSA S16 · Step-by-step calculation reports

What is the Elastic Critical Moment?

Mcr is the bending moment at which a perfectly straight, elastic beam becomes unstable: the compression flange moves sideways and the section twists. Real beams fail below this value because of imperfections, residual stresses and yielding, so design standards use Mcr as the input to a slenderness and a reduction factor rather than as a resistance.

For a doubly symmetric beam on fork supports under uniform moment there is an exact expression:

Mcr = (π²EIz / L²) √( Iw/Iz + L²GIT / (π²EIz) )

Every other case (a moment gradient, a load on the top flange, a restraint part-way along, a cantilever, unequal flanges) needs either tabulated factors such as C1 and C2, which cover a limited set of cases, or a buckling analysis. EN 1993-1-1 gives no expression for Mcr at all: clause 6.3.2.2(2) only requires that it is based on gross section properties and takes account of the loading conditions, the real moment distribution and the lateral restraints.

How This Calculator Works

The beam is divided into at least 32 thin-walled beam elements with four degrees of freedom per node: lateral displacement, lateral rotation, twist and warping. The elastic stiffness comes from lateral bending (EIz), St Venant torsion (GIT) and warping (EIw). The destabilising terms come from the actual bending moment diagram, the height of each load above the shear centre and, for unequal flanges, the monosymmetry of the section. The lowest positive eigenvalue is the factor on the entered loading at which the beam buckles, and Mcr is that factor times the largest moment in the beam.

The analysis is repeated on a mesh twice as fine; if the two results differ by more than 0.1 % a warning is shown.

Load Height

A downward load applied to the top flange moves sideways with the flange as the beam twists and adds to the twist: a destabilising load. The same load hung from the bottom flange pulls the section back. The effect is largest for short, deep beams and for cantilevers, where a top-flange load can halve Mcr. What matters is the direction of the load relative to the shear centre, so an uplift load on the top flange is stabilising. End moments have no load height.

Supports and Restraints

A fork support prevents lateral movement and twist but leaves the flanges free to rotate in plan and the section free to warp; this is the standard assumption behind tabulated formulae. Preventing warping, for example with thick end plates and stiffeners, or lateral bending raises Mcr. A cantilever is taken as fully built in at its support.

An intermediate restraint holds one flange level against lateral movement, or both flanges, which also prevents twist. A restraint on the compression flange is far more effective than one on the tension flange, and in a beam with moment reversal the compression flange changes side along the length. Restraints are treated as rigid.

Using Mcr in Design

In Eurocode 3 the non-dimensional slenderness for lateral-torsional buckling follows directly from Mcr, and the reduction factor χLT from the buckling curve for the section:

λ̄LT = √( Wy fy / Mcr )

Other standards have equivalent routes: AS 4100 clause 5.6.4 allows the member moment capacity to be based on an elastic buckling analysis, and CSA S16 clause 13.6.1 calls for a rational method for cantilevers and for loads applied above the shear centre. Check which adjustments your standard already makes for moment gradient before combining them with a value from this page. For the full member check to Eurocode 3, use the EN 1993-1-1 design calculator.

Verification

The analysis behind this page is checked against independent solutions:

  • The exact expression above for uniform moment on fork supports: within 0.001 %.
  • An independent series solution for fork-ended beams (end-moment ratios from 1 to −1, uniform and midspan loads at the top flange, shear centre and bottom flange, midspan restraints at each level, unequal flanges): 19 cases within 0.01 %.
  • The exact differential-equation solution for cantilevers with tip and uniform loads at each load level: 12 cases within 0.001 %.
  • The published closed form for unequal-flange beams under uniform moment, with either flange in compression: within 0.001 %.
  • An independent finite element analysis with warping beam elements, including a warping-fixed beam and a cantilever: within 0.002 %.

Tabulated C1 factors are approximate and usually rounded to the safe side, so this calculator can return a few per cent more than a hand calculation with them.

Assumptions and Limits

  • Straight, prismatic, elastic beam bent about its major axis, with loads in the plane of the web that keep their direction as the beam buckles.
  • Library sections cover I-sections, channels, tees, hollow sections, single angles and solid bars. Channels are taken as loaded through the shear centre, and angles as bent about the major principal axis; an angle loaded parallel to a leg bends about both axes and is not covered.
  • Round and square hollow sections, and other sections as stiff sideways as in the plane of bending, do not buckle laterally in practice; the page says so when one is chosen.
  • A single span or cantilever. Represent continuity over a support with end moments; the adjacent spans are not modelled.
  • Deflection before buckling, distortion of the web and local buckling are not included.
  • Welded I-sections ignore root fillets, which lowers IT noticeably for rolled sections. Enter catalogue properties for rolled sections.
  • No axial force. No concentrated moment at a cantilever tip.
  • Mcr is an elastic buckling value, not a design resistance.

Related Calculators

Check the Whole Frame, Not One Beam

3D structural analysis with Eurocode 3 member design checks on every member and load combination. Free, no signup required.