Skip to main content

Node Links

A node link makes chosen directions of a slave node follow a master node, with no member between them. Use it for rigid arms between offset nodes and for pins or hinges between groups of members that meet at a joint.

When to use a node link

SituationUse
One member pinned or hinged at its end (for example a beam pinned to a continuous column)The member's end releases. They act about the member's own axes, so they also suit inclined members.
A group of members hinged to another group at a shared joint (scissor X-brace, pinned clevis between two continuous members)Hinge Members at Joint or Make Scissor Joint
Two nodes apart joined by something much stiffer than the members (a bracket, a deep end plate, centrelines that don't line up)A node link: Rigid link, or Pin (3D) for an arm pinned at its far end
A whole floor or wall moving as one in its planeA rigid diaphragm

The link code

Each link has a six-letter code in the order DX DY DZ RX RY RZ, in global axes. F means the slave follows the master in that direction; R means it is free. At least one direction must be F. Choose a Link type, or click a direction in the dialog to tie or free it (the type then shows Custom).

Link typeCodeBehaviour between nodes at the same point
Rigid linkFFFFFFForce and moment pass in every direction.
Pin (3D)FFFRRRForce passes in every direction; no moment.
In-plane pin (XY models only)FFRRRROnly X and Y force passes. In a 3D model the nodes are unconnected along Z.
Hinge about global X / Y / ZFFFRFF / FFFFRF / FFFFFREverything passes except moment about the hinge axis.

Hinge axes are global X, Y or Z only. For a pin about an inclined axis, use member end releases instead.

When the master is supported, a tied direction its supports hold shows as F⏚: the slave is effectively supported in that direction too.

Offset nodes: a rigid arm

At the same point, the code is plain equality: each F direction of the slave moves exactly as the master's. When the nodes are apart, the link is a rigid arm from the master to the slave:

  • Each tied translation follows the master as a rigid body, including the movement from all three master rotations acting over the offset. A force through the arm therefore reaches the master with its moment over the gap.
  • The rotation letters decide only whether the slave's own rotation follows the master. An offset FFFRRR link is a rigid arm pinned at the slave: the arm turns with the master and the slave rotates freely on its end. The dialog states this when you set one up.
  • A tie only along the line between the nodes (for example FRRRRR with the nodes apart along X) is a pinned strut and involves no rotation.

In P-Delta and buckling analysis, force carried by an offset link acts on the arm as on a rigid bar: compression along the arm reduces stability and tension increases it.

Constraint equations

Lx, Ly, Lz are the global components of the offset from the master to the slave. D is a translation and R a rotation; subscript s is the slave and m the master. Each row applies only when that direction of the code is F. A free direction has no equation: the slave moves independently there.

Tied directionEquation
DXDx,s = Dx,m + Lz·Ry,m − Ly·Rz,m
DYDy,s = Dy,m + Lx·Rz,m − Lz·Rx,m
DZDz,s = Dz,m + Ly·Rx,m − Lx·Ry,m
RX, RY, RZRx,s = Rx,m, Ry,s = Ry,m, Rz,s = Rz,m

The rotation terms in the translation rows are kept whatever the rotation letters are, because the master turns the whole arm. At the same point every offset is zero and the rows reduce to plain equality, for example Dx,s = Dx,m.

Example. A beam sits on a bracket 0.5 m out from a column, pinned at the beam end: master at the column, slave at the beam end, code FFFRRR. A 10 kN load at the beam end reaches the column as 10 kN plus 10 × 0.5 = 5 kN·m from the arm, and the beam end still rotates freely on the pin.

Some programs drop the rotation terms when the matching rotation is free, so an offset FFFRRR there passes the force but not its moment over the gap, and the results no longer balance. Here the moment is always carried. For a link that passes force only, put the two nodes at the same point.

Adding a node link

  1. Select the nodes. Right-click and choose Add Node Link, or click Add Node Link under Constraints in the Properties panel. If the item is greyed out, hover over it to see why.
  2. The dialog proposes a master: a single selected node, or, with several, the only supported one (otherwise the first selected). The other nodes become slaves. Change them with Pick from canvas or Swap.
  3. Choose the Link type and, optionally, a name.
  4. Resolve any red messages and click Add link (Add N links with several slaves). One link is created for each slave.

Hinge Members at Joint

Members meeting at a node are joined rigidly. Hinge Members at Joint… moves the members you choose to a new node at the same point and joins it to the original node with a link (default Pin (3D)). The other members stay rigidly connected to the original node, so each group remains continuous through the joint and the two groups are hinged to each other.

From a node (one joint):

  1. Right-click the joint node and choose Hinge Members at Joint….
  2. Tick the members to hinge, or use Pick in the model. Leave at least one member unticked. At a node joining only two members, one is already ticked.
  3. Choose the link type and click Hinge (the button shows the number of members).

From members:

  1. Select the members that stay on the original node, right-click one and choose Hinge Members at Joint….
  2. If only one other member meets the staying members, it is taken as the member to hinge and this step is skipped. Otherwise the dialog shrinks to a bar: click the members to hinge at the joint and press Use selection. Picked members that don't meet the staying members are left as they are. At an X-brace crossing the bar points to Make Scissor Joint, which splits the two braces in one step.
  3. Choose the link type and click Hinge. Members are hinged at every node the two groups share; to hinge at one joint only, start from the node.

Supports, settlements, nodal loads and masses stay on the original node; the hinged members reach them only through the directions the link ties. The dialog warns when the groups share more than one joint, when the joint is supported, when a Rigid link would change nothing, when the code leaves the hinged members free to translate (the analysis would stop with an instability unless other members hold them), and when the node already follows another constraint.

Make Scissor Joint

For an X-brace whose two braces are each split at the crossing, right-click the crossing node and choose Make Scissor Joint. The command finds the two straight braces, keeps one on the original node, moves the other to a new node at the same point, and joins them with a Pin (3D) link named "Scissor joint". Each brace stays continuous through the crossing; the braces share translations but rotate independently. Select several crossing nodes to do them together; nodes that don't qualify are skipped and listed when you hover the menu item. Tension-only and compression-only braces are accepted.

The command appears when a selected node has four members. It works from geometry alone, so it refuses joints that look like moment connections, and joints it cannot split safely:

  • A line within 10° of vertical: treated as a column. To pin a beam to a column, release the beam end.
  • Two horizontal lines crossing square along the global X and Z grid: treated as a floor-beam grid. Diagonal plan bracing is accepted. A beam grid set off the global axes is not recognised, so check the members named in the confirmation message.
  • Not two straight braces: the four members must form two straight lines through the node.
  • A support, spring support or settlement at the node: the new node would have none, so one brace would lose it.
  • A plate at the node, or a node already in a node link or rigid diaphragm.

For a brace pair it refuses, or any other group of members, use Hinge Members at Joint….

Supports and loads at linked nodes

  • A slave can't be supported, or given a settlement, in a direction it has tied. Put the support on the master, or free that direction in the code.
  • The original node of a hinged or scissor joint is the master and keeps its supports and loads. A node load applied to a selection that includes several nodes of one joint (for example a box selection) is applied once, to the master, and a message says so.
  • Clicking the same spot again selects the next node at that point; a message names the node you have. New members drawn to the joint connect to the master.

Link forces

Linear static and P-Delta analyses, including models with tension-only or compression-only members, report the force through each enabled link. Modal and buckling analyses do not.

  • Values are the force and moment the master applies to the slave through the link, in global axes, acting on the slave node (Fx, Fy, Fz, Mx, My, Mz). Free (R) directions carry none.
  • The master receives the opposite force plus that force's moment over the offset.
  • They appear in the Node Links tab of the results, on the link row in the Properties panel when a linked node is selected, and in the PDF and Excel reports. For several combinations, each link shows the combination with the largest force resultant.

Model Health

The dialog checks a link as you define it. Model Health checks every link in the model, including imported ones, before you run an analysis, and also catches problems that come from later edits.

ConditionResult
Slave supported, or given a settlement, in a tied directionBlocked. Move the support or settlement to the master, or free that direction.
A slave direction already tied by another link or a rigid diaphragmBlocked: a direction can follow only one master. Tying different directions is fine.
Links forming a loop in a shared direction (A follows B, B follows A)Blocked. Remove one tie from the loop.
Rotation tied at a node connected to a plateBlocked: it over-stiffens the plate locally. Free the rotations, for example with Pin (3D).
Plate node as the master of an offset linkBlocked: a plate node can't drive a rigid arm. Make the plate node the slave, put the nodes at the same point, or end the member on a plate node without a link.
A linked node lying along a member but not at its endsBlocked: the analysis would also tie the member there. Connect the member with Intersect, or move the node.
A plate node along a member, used as the slave of an offset link that ties translationsBlocked: the model can't be analysed. Put the nodes at the same point, or connect the member to the plate without a link.
Plate mesh node, or the reference node a rigid diaphragm createsBlocked. Link a joint or plate corner node instead.
Chain: a master that itself follows another link or a diaphragmWarning: supported, check it is intended.
A rigid diaphragm's master that is the slave of a linkWarning: the whole diaphragm follows the link's master in the tied directions.
A turned-off link between two nodes at the same point that both carry membersWarning: the members on the two nodes are not connected.
Members reaching a support only through a link that does not tie all six directionsWarning: stable only if the free directions are restrained elsewhere.

Two nodes joined by a link are not reported as duplicate nodes, even at the same point.

Editing, display and deletion

  • Select a master or slave node and click the link under Constraints to edit it or delete it. The checkbox beside it turns it on or off, with the same checks as the dialog.
  • Turned-off links stay in the model but are ignored in analysis and not drawn.
  • Enabled links are drawn in cyan, labelled with their code; links between offset nodes also show a dashed line.
  • Moving a hinged or scissor joint, with Move, by typing a coordinate in the Properties panel or by editing one of its nodes in the Node Definitions table, moves all its nodes together. If one edit moves the joint's nodes by different amounts, it is kept as typed and a warning says so: the link is then a rigid arm between two points. Mirror without keeping the original keeps the joint linked.
  • Deleting a node deletes its links. Deleting or turning off the link of a hinged joint leaves the two groups of members disconnected; the edit dialog warns about this.
  • Members can't be merged through a linked node.

Limits

  • Codes act in global axes only.
  • Each link joins one master to one slave. Linking one master to several slaves creates one link per slave.